background image

10

Blade Inspection

1. Turn the fuel valve OFF (

page 3

).

2. Disconnect the spark plug cap from the spark plug (

page 12

).

3. Tilt the mower to the right side so that the fuel cap side is up. This

will help to prevent fuel leakage and hard starting due to carburetor

flooding.

4. Inspect the blade for damage, cracks, and excessive rust or

corrosion.

A dull blade can be sharpened, but a blade that is excessively worn,

bent, cracked, heavily rusted, or otherwise damaged must be

replaced.

If a blade is bent, take the lawn mower to an authorized Honda

servicing dealer for inspection.

Blade Mounting Bolt Inspection

Inspect the blade bolts for any signs of damage

or looseness. If they are damaged, they must

be replaced.
If they appear loose, a torque wrench must be

used to accurately tighten the blade bolts to the

required torque. If you do not have a torque

wrench, take your lawn mower to an authorized

dealer to have the bolts replaced or tightened.
Use only Honda Genuine blade bolts and

special washers, since they are specifically

designed for this purpose. Replacement part

numbers are on 

page 18

.

Blade Replacement

1. Turn the fuel valve OFF (

page 3

).

2. Disconnect the spark plug cap from the spark plug (

page 12

).

3. Tilt the mower to the right side so that the fuel cap side is up. This

will help to prevent fuel leakage and hard starting due to carburetor

flooding.

4. Remove the two blade bolts with a 14 mm (6 point) socket wrench.

Use a wooden block to prevent the blade from turning when

removing the bolts. Remove the blade. Do not loosen the center

blade holder bolt.

5. Clean dirt and grass from around the blade mounting area.
6. Install the sharpened or replacement blade using the two blade

bolts and special washers as shown above. Be sure to install the

concave side of the washer up (towards the engine).
The blade bolts and washers are specially designed for this

application. When replacing bolts and washers, use only Honda

Genuine replacement parts.

7. Tighten the blade bolts with a torque wrench to the specified

torque. Use a wooden block to prevent the blade from turning

when tightening the bolts.

Blade bolt torque: 

36 ~ 43 ft-lb (49 ~ 59 N·m)

If you do not have a torque wrench, have an authorized Honda

servicing dealer tighten the blade bolts.

 WARNING

A worn, cracked, or damaged blade can break, and 
pieces of the damaged blade can become dangerous 
projectiles.

A blade thrown from the mower could seriously hurt or 
kill someone.

Inspect the blade regularly, and do not operate the 
mower with a worn or damaged blade.

BLADE

BLADE BOLTS

NORMAL

WORN

BENT

CRACKED

NORMAL 

TRAILING EDGE

EXCESSIVELY WORN 

TRAILING EDGE

 WARNING

If the blade bolts are not torqued properly, the blade 
could loosen and be thrown from the mower. 

A blade thrown from the mower could seriously hurt or 

kill someone.
Ensure the blade bolts are torqued properly.

Inspect washers and 

bolt heads for 

looseness and 

damage.

BLADE HOLDER

 BLADE

SPECIAL
WASHER (2)

BLADE BOLT (2)

Summary of Contents for SHRX217HYA

























Reviews: