background image

13

Oil Change

Change the oil after the first month or 5 hours of use. Thereafter, 
change the oil every 6 months or 50 hours of use. Change the oil 
more frequently when used under heavy load or high outdoor 
temperatures. See “Engine Oil Recommendations” on this page for 
recommended oil properties.

Drain the used oil while the engine is warm. Warm oil drains quickly 
and completely.

To reduce the chance of scratching the side of the mower deck or

wheels when tipping, place a piece of cardboard or drop cloth on the

ground. The use of a commercially available siphon pump will save

time and make the oil change easier.

1. Turn the fuel valve OFF (

page 3

). This will reduce the possibility of

fuel leakage.

2. Wipe the oil filler area clean, and then remove the oil filler

cap/dipstick.

3. Place a suitable container

next to the mower to catch

the used oil, and then tilt the

mower on its right side.
The used oil will drain

through the filler neck. Allow

the oil to drain completely.
After draining, take the oil to

your local recycling center or

service station. Do not throw

it in the trash, pour it on the

ground, or pour it down a

drain.

4. Fill with the recommended oil.

Do not overfill. Allow a couple

of minutes for the oil to settle

in the engine, and then

measure the oil level

(

page 4

).

Refill amount:

 

12.0 ~ 13.5 oz 

(0.35 ~ 0.40 L)

NOTICE

Using non detergent oil can

shorten the engine’s service

life, and using 2-stroke oil can damage the engine.

Engine Oil Recommendations

Oil is a major factor affecting performance and service life. Always

change the oil in accordance with the 

Maintenance Schedule

(

page 11

).

Recommended oil for general use:

 SAE 10W-30 

Other viscosities shown in the chart may be used when the average

temperature in your area is within the recommended range.

The SAE oil viscosity and service category are in the API label on the

oil container. Honda recommends API service category SJ or later oil.

Air Filter

Clean the air filter after the first 25 hours of use. Thereafter, clean the 
filter every 6 months or 50 hours of use. Clean the filter more often 
when used in dusty areas. Replace the filter every 2 years or 150 
hours of use.

A properly maintained air filter will help prevent dirt from entering your

engine. Dirt entering the carburetor can be drawn into small passages

in the carburetor and cause premature engine wear. These small

passages can become blocked, causing starting or running problems.

NOTICE

Operating the engine without an air filter, with a damaged air filter, or

with an improperly installed air filter cover will allow dirt to enter the

engine, causing rapid engine wear. This type of damage is not

covered by the DISTRIBUTOR’S LIMITED WARRANTY (

page 21

).

We recommend the use of a Honda Genuine air filter to ensure it

seals and performs as designed. Using a non-Honda air filter can

result in dirt bypassing the filter, causing damage to the engine or fuel

system.

 WARNING

If the blade bolts are not torqued properly, the blade could 

loosen and be thrown from the mower. 
Blades thrown from the mower could seriously hurt or kill 

someone.
Ensure the blade bolts are torqued properly.

TORQUE 
WRENCH

TORQUE: 
36 ~ 43 ft-lb 
(49 ~ 59 N•m)

BLADES

WOODEN BLOCK

-20

20 30 40°C

-10

0

10

40

60

100°F

80

0

20

30

5W-30 • 10W-30

Summary of Contents for WeatherMaker 48KC

























Reviews: