Honeywell Home LTEM-PA Installation And Setup Manual Download

Page: 31 / 36

Appendices

Appendix A: Summary of LED Operation

LTEM-P Initial Power Up

: Upon initial power up, the communicator LEDs blink in repeated sequence from top

to bottom indicating network initialization.

Green (REG)



Yellow (STATUS)



Red (FAULT)



Green (CELL)



Green (WIFI)

LED INDICATIONS

LED

DESCRIPTION

Power On Indication

: If AC is present, Status

(yellow) LED blinks periodically. If on battery power
only for longer than 5 minutes (AC loss), the LEDs
turn off, then blink once per minute in a random
pattern.

REG
(green)

Module is NOT registered with AlarmNet

OFF

Module is registered with AlarmNet

FAST BLINK Download session with Compass in progress
SLOW BLINK In unison with STATUS (yellow) LED,

registration in progress

STATUS
(yellow)

PERIODIC

BLINK

Normal (indicates Power On*)

FAST BLINK Cannot deliver alarms

SLOW BLINK

Idle power abnormal
In unison with REG (green) LED, registration
in progress

FAULT
(red)

No contact with the network

OFF

Normal

FAST BLINK No network contact AND loss of

communication with the panel

SLOW BLINK Loss of communication with the panel (ECP

fault)

CELL
(green)

Minimum required signal quality is present

OFF

Cell not enabled

FAST BLINK Signal quality is poor

WI-FI /
ETHERNET
(green)

Wi-Fi Connection (if used)

Communicator connected to Internet via Wi-Fi

OFF

Wi-Fi not enabled

FAST BLINK Wi-Fi enabled, no connection to Internet

Ethernet Connection (if used)

Communicator connected to Internet via
Ethernet

OFF

Ethernet not enabled

FAST BLINK Ethernet enabled, no connection to Internet

TOP THREE
- REG
- STATUS
- FAULT

FAST BLINK
IN UNISON

Firmware over-the-air (OTA) download in
progress

TOP FOUR
- REG
- STATUS
- FAULT
- CELL

FAST BLINK
IN UNISON

Cell module firmware OTA update in progress

ALL FIVE LEDs
- REG
- STATUS
- FAULT
- CELL
- WI-FI /

ETHERNET

FAST BLINK
IN UNISON

SIM card not present or puk locked

FAST BLINK
IN SEQUENCE

Power up sequence

LEDs 1, 3, & 5
- REG
- FAULT
- WIFI

FAST BLINK
IN UNISON

Unit is in Pairing mode (connecting to smart
device via Bluetooth)

Summary of Contents for LTEM-PA





































Search results

Summary of Contents for LTEM-PA

Reviews:

Related manuals for LTEM-PA

Brands by name

Popular brands

Honeywell Home LTEM-PA, Installation And Setup Manual

Search results

Summary of Contents for LTEM-PA

Reviews:

Related manuals for LTEM-PA

Brands by name

Popular brands