background image

Step 2. 

Step 2. 

Step 2. 

Step 2. 

Step 2. 

Open Safe with Override Key (square top)

Open Safe with Override Key (square top)

Open Safe with Override Key (square top)

Open Safe with Override Key (square top)

Open Safe with Override Key (square top)

You will need access to the inside of the safe door to begin

programming.  You must use the Emergency Override Key

(square top) to open the door for the first time.

1. Insert the Emergency Override Key (square top) in the

lock, turn to the left 

left 

left 

left 

left (counterclockwise) and pull the door open.

Step 1.

Step 1.

Step 1.

Step 1.

Step 1.

 Installing Batteries

 Installing Batteries

 Installing Batteries

 Installing Batteries

 Installing Batteries

The digital keypad is powered by 4 “AA” batteries which

must be installed before you can begin programming

your personal code.  For your convenience, we have

provided you with 4 “AA” batteries.  

For best results and

depending on use, we recommend replacing the

batteries at least once a year.

1. Locate battery compartment to the right of the

digital keypad.

2. To open the compartment, press firmly in on the

battery cover and slide it to the right for removal.

3. Install 4 new “AA” batteries in the battery

compartment. Make sure they are installed in the

correct direction as marked on the inside of the

battery compartment.

4. Once the batteries are installed properly, replace

the cover by sliding it back on from the left.

2

22

22

Programming Preparation

Programming Preparation

Programming Preparation

Programming Preparation

Programming Preparation

Important: 

Important: 

Important: 

Important: 

Important:  BATTERY REMOVAL

BATTERY REMOVAL

BATTERY REMOVAL

BATTERY REMOVAL

BATTERY REMOVAL

If the batteries are removed or fail, the

keypad memory will 

NOT

NOT

NOT

NOT

NOT     

be erased.

Important: 

Important: 

Important: 

Important: 

Important: TURN OVERRIDE KEY TO LEFT ONLY

TURN OVERRIDE KEY TO LEFT ONLY

TURN OVERRIDE KEY TO LEFT ONLY

TURN OVERRIDE KEY TO LEFT ONLY

TURN OVERRIDE KEY TO LEFT ONLY

When using the Emergency Override Key, you

must 

ONLY TURN IT TO THE LEFT

ONLY TURN IT TO THE LEFT

ONLY TURN IT TO THE LEFT

ONLY TURN IT TO THE LEFT

ONLY TURN IT TO THE LEFT

.  Turning it

to the right may cause key to become stuck in

the cylinder and may cause damage to the lock.

BATTERY

COMPARTMENT

Notes

Notes

Notes

Notes

Notes

11

11

11

11

11

Home and Office Security Safes

Summary of Contents for 2054D















Reviews: