READ IT
OR
WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit bit.ly/2KGwKxc
44127 (10IN.), 44128 (16IN.)
PLUG-IN
LED LIGHT FIXTURE
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR CABINET
SO YOU CAN REFER TO THEM AT A LATER TIME.
CAUTION: DO NOT OVER TIGHTEN SCREWS
DO NOT USE WITH A DIMMING CIRCUIT OR ANY OTHER
ELECTRONICALLY SWITCHED CONTROL.
IMPORTANT SAFETY INSTRUCTIONS
The LED light fixture has a polarized plug (one blade is wider than the other) as a feature to
reduce the risk of electric shock. This plug fits in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can be fully inserted. Do not alter the plug. Read
entire installation procedure before you begin.
INSTALLATION PROCEDURE FOR PLUG-IN LED LIGHT FIXTURE
Carefully plan out your installation prior to actually securing your LED light fixture to the
mounting surface making sure that your 5ft. line cord will reach the nearest electrical outlet. For
kitchen installations, the recommended mounting for the LED light fixture is near the front lip
of your kitchen under cabinets as shown in the illustration
Figure 1.
This provides the best light
distribution across a countertop.
1. DO NOT ATTEMPT TO INSTALL LED LIGHT FIXTURE
WHILE
PLUGGED IN.
2. Select a suitable dry mounting location (for use
indoors only). Make sure mounting surface is capable
of supporting the LED light fixture.
3. Hold the LED light fixture in desired location and
clearly mark the locations for the mounting holes.
4. Using a 3/32in. drill bit, pre-drill holes into the
mounting surface. Mounting is via keyholes; when
inserting the provided screws, leave 1/8in. of the
screw heads protruding beyond the mounting surface.
5. Mount the LED light fixture to surface by aligning
screws to keyholes and sliding into place to secure, as
shown in
Figures 2 and 3.
If necessary, tigthen screws
to secure in place.
6. Plug the LED light fixture into a 120VAC 60Hz outlet.
Suppliers Declaration of Conformity | Model #: 44127 | 44128 | Jasco Products Co., 10 E.
Memorial Rd, Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interfer- ence in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communica- tions. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interfer- ence by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Questions? Contact our U.S.-based Consumer Care at 1‑855‑654‑8483,
Monday–Friday, 7AM–8PM, Central Time.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and
more, visit www.byjasco.com/support.
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
FCC/IC - EN
SPECIFICATIONS
The Honeywell trademark is used under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
This product is manufactured by Jasco Products Company LLC.
This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for warranty details.
MADE IN CHINA/HECHO EN CHINA
©JASCO 2020 | 44127, 44128 | 01/10/2020 v2
Jasco Products Company LLC.
10 E. Memorial Road
Oklahoma City, OK 73114
120VAC 60Hz
4.95W
340 Lumens
81 CRI
2700K CCT White
120VAC 60Hz
5.85W
445 Lumens
81 CRI
2700K CCT White
44127 (10IN.)
44128 (16IN.)
FIGURE 1
CABINET
COUNTER TOP
W
ALL
CLEANING INSTRUCTIONS
Your LED light fixture is made from quality materials that will last
for many years with minimum care. When cleaning, make sure
you have unplugged your LED light fixture and have allowed a
sufficient amount of time for it to cool to room temperature. You
should clean the housing and lens using a soft, damp cloth. Do
not use chemicals to clean your LED light fixture, as this could
damage or discolor your LED light fixture. You should plug your
LED light fixture back in only after it has thoroughly dried.
RISK OF ELECTRICAL SHOCK
• DO NOT USE IN WET LOCATIONS
• USE INDOORS ONLY
• USE ONLY INSULATED STAPLES OR
PLASTIC TIES TO SECURE THE CORDS
• ROUTE AND SECURE THE CORDS SO
THAT THEY WILL NOT BE PINCHED OR
DAMAGED
NO SERVICEABLE PARTS
NON-REPLACEABLE LEDS
LED LIGHT OUTPUT IS STRONG
ENOUGH TO INJURE HUMAN EYES.
PRECAUTIONS MUST BE TAKEN TO
PREVENT LOOKING DIRECTLY AT THE
LEDS WITH UNAIDED EYES FOR MORE
THAN A FEW SECONDS.
RISK OF FIRE
• NOT INTENDED FOR ILLUMINATION OF
AQUARIUMS
• NOT INTENDED FOR USE ABOVE
STOVES, COOK TOPS, SINKS OR OTHER
HEAT PRODUCING APPLIANCES, SUCH
AS COFFEE MAKERS, TOASTERS, OR
TOASTER OVENS
• NOT INTENDED FOR RECESSED
INSTALLATION IN CEILINGS OR
SOFFITS
• NOT INTENDED FOR SURFACE
INSTALLATION INSIDE OR ON TOP
OF BUILT‑IN FURNISHINGS SUCH AS
KITCHEN CABINETS, CHINA CABINETS,
OR TROPHY CASES
• DO NOT CONCEAL POWER SUPPLY
CORD OR LINKING CORDS INSIDE
A WALL, CEILING, SOFFIT, KITCHEN
CABINET, OR SIMILAR PERMANENT
STRUCTURE
• DO NOT RUN THE POWER SUPPLY
CORD OR LINKING CORDS THROUGH
HOLES IN WALLS, CEILINGS OR
FLOORS
WARNING
FIGURE 3
INSERT
SLIDE
FIGURE 2
CABINET
