![background image](http://html.mh-extra.com/html/honeywell/4800dr-document-camera/4800dr-document-camera_barcode-manual_22261044.webp)
5 - 2
value for that symbology and scan the 2 digit hex value from the
Programming Chart
inside the
back cover of this manual.
Step 5.
Length
Specify what length (up to 9999 characters) of data will be acceptable for this symbology.
Scan the four digit data length from the
Programming Chart
inside the back cover of this man-
ual. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all
lengths.)
Step 6.
Editor Commands
Refer to
Data Format Editor Commands
(page 5-2). Scan the symbols that represent the com-
mand you want to enter. 94 alphanumeric characters may be entered for each symbology
data format.
Step 7.
Scan
Save
from the
Programming Chart
inside the back cover of this manual to save your
entries.
Other Programming Selections
•
Clear One Data Format
This deletes one data format for one symbology. If you are clearing the primary format, scan
0
from
the
Programming Chart
inside the back cover of this manual. If you are clearing an alternate format,
scan
1
,
2
, or
3
, depending on the alternate format you are clearing. Scan the Terminal Type and Code
I.D. (see
Supported Terminals
on page 1-3), and the barcode data length for the specific data format
that you want to delete. All other formats remain unaffected.
•
Save
from the
Programming Chart
inside the back cover of this manual
This exits, saving any Data Format changes.
•
Discard
from the
Programming Chart
inside the back cover of this manual
This exits without saving any Data Format changes.
Data Format Editor Commands
Send Commands
F1
Send all characters followed by “xx” key or function code, starting from current cursor position.
Syntax = F1xx
(xx stands for the hex value for an ASCII code, see
ASCII Conversion Chart
(Code Page 1252)
, page A-3.)
F2
Send “nn” characters followed by “xx” key or function code, starting from current cursor position.
Syntax = F2nnxx
(nn stands for the numeric value (00-99) for the number of characters and xx
stands for the hex value for an ASCII code. See
ASCII Conversion Chart (Code Page
1252)
, page A-3.)
F3
Send up to but not including “ss” character (Search and Send) starting from current cursor posi-
tion, leaving cursor pointing to “ss” character followed by “xx” key or function code.
Syntax =
F3ssxx
(ss and xx both stand for the hex values for ASCII codes, see
ASCII Conversion Chart
(Code Page 1252)
, page A-3.)
F4
Send “xx” character “nn” times (Insert) leaving cursor in current cursor position.
Syntax =
F4xxnn
(xx stands for the hex value for an ASCII code, see
ASCII Conversion Chart (Code Page
1252)
, page A-3, and nn is the numeric value (00-99) for the number of times it should be sent.)
E9
Send all but the last “nn” characters, starting from the current cursor position.
Syntax = E9nn
(nn is the numeric value (00-99) for the number of characters that will not be sent at the end of
the message.)
Summary of Contents for 4800dr - Document Camera
