background image

7 - 5

OCR User-Defined Variables

You can create up to two of your own user variables for an OCR template.  These variables will represent 
any OCR readable characters.  The user-defined variables are stored under the letters “g” and “h.”  Cre-
ating a user variable follows the same steps as creating a template, but instead of scanning the 

Enter 

OCR Template 

symbol, you scan the 

Enter User-Defined Variable

 symbol (

page 7-10

).  The letters g 

and h can then be used in an OCR template to define the variable you specified.

Example:

You need a variable to represent the letters “A,” “B,” or “C.”  The template for this variable 
would be:

414243

To create this template, you would enable the OCR-A font.  Scan the 

Enter User-Defined Variable g

 

symbol (

page 7-10

).  Scan 

414243

 from the 

Programming Chart

 (the hex characters for “A,” “B,” and 

“C”).  Scan 

Save OCR Template 

(

page 7-10

).  This will let you read either A or B or C in any position 

where you place the g.  For example, you could create the following template:

ddddddggg

This template would then let you read data that began with six digits, and had an A, B, or C trailing.  So 
you would be able to read:

654321ABC

or

654321BAC

or

654321CCC

Reading Multi-Row OCR

The  imager is capable of decoding multi-row OCR text.  

Note:

Reading rows longer than sixteen characters is not recommended.

Consider the following example.  This example shows serial commands as they would be entered using 
Quick*View.

Example:

  You need to read multiple rows of OCR-A data as shown below:

12345678
ABCDEFGH

First, enable the OCR-A font.  To read the first row of OCR data, you would program the following 
template:

OCRTMP"dddddddd".

This template is the default OCR template.  If you wanted to read the second line of data, you would 
use the following template: 

OCRTMP"llllllll".

Summary of Contents for 4800dr - Document Camera



















































































































































Reviews: