background image

 

MOUNTING (

Model 5215)

 

 

1.

 

Unlock the safe and Pull the drawer out until it stops. On each of the drawer glides there 
is a small plastic latch. To remove the drawer you need to simultaneously push down on 
the right side latch while pulling up on the left side latch putting forward pressure on the 
drawer as you do. This will release the drawer from the drawer glides and allow the 
drawer to be removed. 

 

 

2.

 

Determine if you want to secure the safe to the wall on onto the floor and then select  
a  suitable and convenient location.  

3.     Locate the predrilled holes on the inside of safe. 
4.     Place your safe in the desired location. 
5.     Line up the predrilled holes and mark the floor or wall through the holes. NOTE: It is not        

recommended to attempt to bolt to both floor and wall. 

6.     Move the safe aside to clear marked spots for drilling. 
7.     Drill holes appropriate for hardware being used and the mounting surface.  
        INCLUDED: (2 each – bolts, washers and masonry anchors). 
8.     Place the safe back over the holes and install the fasteners as required. 

 

It is important to note that if prior to installation you have any questions and/or concerns regarding 
the proper securing of the safe to a wall or floor you should check with your local home center / 
hardware retailer or independent contractor. The securing of the safe to a wall or floor is at the 
consumer’s expense and discretion. LHLP, Inc. is not responsible for any costs incurred if the unit 
is damaged and needs to be replaced.

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 5203










Reviews: