Honeywell ADEMCO LYNX XL Series Installation And Setup Manual Download

Page: 38 / 76

LXL-1010 Installation and Setup Guide

5–2

PROMPT

VALID ENTRIES

EXPLANATION

10 Zone Type
Perimeter 03

Zone Type (ZT)

00-24, 90, 91 = zone type (see
table at right)

Each zone must be assigned to a zone type, which defines the way in
which the system responds to faults in that zone.
Enter the Zone Type code from the list below:

Note:

If 00 is entered,

Delete Zone ?

will be displayed.

00 = Not used

07 = 24-Hr Audible

20 = Arm–STAY*

01 = Entry/exit #1

08 = 24-Hr Aux

21 = Arm–AWAY*

02 = Entry/exit #2

09 = Fire

22 = Disarm*

03 = Perimeter

10 = Interior w/Delay 23 = No Alarm Resp*

04 = Interior Follower

12 = Monitor Zone

24 = Silent Burglary

05 = Trouble Day/Alarm Night 14 = Carbon Monoxide
06 = 24-Hr Silent

81 = AAV Monitor Zone

*5800 button-type transmitters only

90-91 = Configurable

10 Report Code

1st 01 2nd 00 10

Report Code (RC)

First Digit:

00 to disable

Second Digit: same as above

[

∗

] to continue

Enter the report code for this zone, which consists of 2 hexadecimal digits,
each in turn consisting of 2 numerical digits. For example, for a report code
of “10,” enter 01 and 00.
For Contact ID

, entering any non-zero entry as the first digit enables the

report code for this zone. Refer to the

System Communication

section for

information about report codes and formats.

10 INPUT TYPE

RF TRANS

Input Device type (In)

3 = RF (supervised RF

transmitter,

4 = UR (unsupervised RF

transmitter)

5 = Button type RF

transmitter
(unsupervised).

[

∗

] to continue

All of the RF transmitters have one or more unique factory-assigned
input (loop) ID codes. Each of the inputs requires its own
programming zone

(e.g., a 5804's four inputs require four

programming zones).
RF Transmitters can be enrolled as one of the following types:

Type Description
“RF”

Sends periodic check-in signals, as well as

(Supervised RF)

fault, restore, and low-battery signals. The
transmitter must stay within receiver's range.

“UR”

Sends all the signals that the “RF” type

(Unsupervised RF)

does, but the control does not supervise the
check-in signals. The transmitter may therefore
be carried off-premises.

“BR”

(Unsupervised Sends only fault signals. It will not send a

Button RF)

low-battery signal until it is activated. The
transmitter may be carried off-premises.

10 INPUT S/N: L

A 0 2 2 - 4 0 6 4 1

Serial number Entry
and Loop Number Entry

see explanation
[

∗

] to continue

a. Transmit two open/close sequences. If using a button-type

transmitter, press and release the button twice, but wait about 4
seconds before pressing the button the second time.

b. Manually enter the 7-digit serial number printed on the label of

the transmitter. Then press the [Q] key – the cursor will move to
the “L” position. You can edit the loop number, if necessary. When
the loop number is acceptable, press [Q].

c. Press key [C] to copy the serial number previously enrolled (used

when programming a transmitter with several input loops).

10 INPUT S/N L

A 0 2 2 - 4 0 6 4 ?

Loop Number Change

[

∗

] to continue

NOTE:

If the [C] key is used to copy the previously enrolled serial

number, the cursor will move to the Loop column (L) with the
previous serial number displayed, and display a highlighted question
mark for the loop number.

Enter the loop number and press [

✱

]. The system will now check for

a duplicate serial/loop number combination.

10 INPUT S/N L

A 0 2 2 - 4 0 6 4 1

Enroll Summary

[

∗

] to continue

If the serial/loop number combination is not a duplicate in the
system, a display showing the serial number and loop number entry
will appear.

www.PDF-Zoo.com