Pager Programming Fields
FIELD
TITLE and DATA ENTRIES
EXPLANATION
*160
Pager 1 Phone No.
Enter up to 20 digits
If you enter fewer than 20 digits, exit by pressing [
∗
] and next field
number. To clear entries from this field, press
∗
160
∗
.
*161
Pager 1 Characters
Enter up to 16 characters
Up to 16 optional characters may be sent as a prefix to the 7-digit
system status code sent to pager #1 (if used). Phone number in field
*160 must have been entered. If fewer than 16 characters, exit by
pressing [
∗
] and next field number. To clear entries from this field,
press
∗
161
∗
.
For example, use these optional 16 characters for the following:
•
PIN number (to identify a specific pager to the paging company)
•
Subscriber account number
•
∗
(enter # + 11 to send
∗
)
•
# (enter # + 12 to send #)
•
Pause (enter # + 13 to allow a 2-second pause)*
•
Any special character(s) the end user may decide to transmit
* Some paging systems require pause(s) before the prefix.
The format for the 7-digit system status code is defined as follows:
Pager Format: XXX-YYYY where:
XXX
= 3-digit event code: 911 = Alarm
811 = Trouble
101 = Opening (disarm)
102 = Closing (arm)
YYYY
= 4-digit user or zone number (depending on type of event).
The first digit indicates partition, followed by 0, then the
2-digit user or zone number.
Example 1.
Pager displays:
9 1 1 – 1 0 0 4
This indicates that the system is reporting an alarm (911) caused by
a fault in zone 4 in partition 1.
Example 2.
Pager displays:
1 0 2 – 2 0 0 5
This indicates that the system is reporting a closing–system arming
(102) by User 5 in partition 2.
*162
Pager 1 Report Options
0 = No reports sent
1 = Open/close for all users enabled to page
†
4 = All alarms and troubles
5 = All alarms, troubles, and open/close for
all users enabled to page
12 = Alarms and troubles for zones entered
in zone list 9
13 = Alarms and troubles for zones listed in
zone list 9 and opens/closes for all
users enabled to page
Enter the types of reports to be sent to pager 1 for each partition.
† Reports to pager only when arming (close)/disarming (open) from a
keypad using a security code; auto-arming/disarming, arming with
assigned RF button, and keyswitch arming do not send pager
messages.
*163
Pager 2 Phone No.
Enter up to 20 digits
If you enter fewer than 20 digits, exit by pressing [
∗
] and next field
number. To clear entries from this field, press
∗
163
∗
.
*164
Pager 2 Characters
Enter up to 16 characters
See field
∗
161 for explanation. If fewer than 16 characters, exit by
pressing [
∗
] and next field number. To clear entries, press
∗
164
∗
.
*165
Pager 2 Report Options
see pager 1 reports, field *162 for entries,
except use zone list 10.
Enter the types of reports to be sent to pager 2 for each partition.
*166
Pager Delay Option for Alarms
0 = none
2 = 2 minutes
1 = 1 minute
3 = 3 minutes
This field determines the delay of alarm reports to the pager. This
gives the Central Station enough time to verify the alarm report that
it received, before the dialer attempts to dial the pager.
NOTE:
The delay does not reset for new alarms occurring while an
existing pager delay is in progress.
This delay is for ALL pagers in the system.
4-9
Summary of Contents for ADEMCO VISTA-48A
Page 4: ......
Page 28: ...Installation Instructions 3 8 ...
Page 60: ...Installation Instructions 5 20 ...
Page 75: ... NOTES 8 5 ...
