background image

10

CM900 Wireless - Programmable Room Thermostat

4.5.2 Category 2 - System Settings

Notes

1) Remember to always press the green   button to confirm that you want to store your new Installer Set-

Up setting. To exit the Installer Mode move the slider switch to the 

AUTO

 or 

MAN

 position.

2) These parameters are set centrally for the zoning system at the room thermostat configured as the 

system synchroniser.

3) Minimum on-time setting applies only to the boiler controller. All Relay Box zone controllers will work 

with the minimum on-time of 30 seconds.

Parameter

Parameter 

No.

Factory Default Setting

Optional Setting

Category 2 Parameters – System Settings (press the 

 button to access this category)

Display

Description

Display  Description

Minimum boiler 
ON time

1:Ot

1

1 minute minimum 
ON time

2 to 5

Selection of 2, 3, 4 or 5 minutes 
minimum ON time

Cycle Rate

2:Cr

6

6 cycles per hour 
(cph)

3,9 or 

12

Selection of 3, 9 or 12 cph

Heat/Cool Change

4:HC

0

Disabled

1

Enabled

Pump Exercise

5:PE

0

Pump exercise 
disabled

1

Pump exercise enabled

System 
Synchronisation

6:Sn

0

Standard operation of 
the Room Unit

1

Room unit configured as Synchroniser

Loss of 
Communications 
Instruction

7:LC

0

Relay Off

1

Relay 20% on / 80% off

The following Parameters are for the control of other Honeywell Wireless products such as Wireless Underfloor Heating 
controls and Wireless Radiator controls. For more information please contact Honeywell sales.

Room Temperature 
Sensor Use

8:Su

0

BDR91 control

1,2,3 

or 4

1 - HR80/HM80 control with own/remote 
sensor (no temperature displayed)
2 - HR80/HM80/HCE80 control with CM 
sensor
3 - BDR91 control and HR80/HM80/
HCE80 control with own/remote sensor
4 – Hr80/HM80/HCE80 control with own/
remote sensor (temperature displayed) 

HR80 Window-
Open Function

9:HO

0

Disabled

1

Enabled

HR80 Local 
Override

10:HL

1

Enabled

0

Disabled

Maximum Flow 
Setpoint

11:uF

55

55°C Maximum Flow 
Temp.

0 to 99

0°C to 99°C adjustment in 1°C steps

Minimum Flow 
Setpoint

12:LF

15

15°C Minimum Flow 
Temp.

0 to 50

0°C to 50°C adjustment in 1°C steps

Mixing Value Run 
Time

13:Ar

150

150 seconds

0 to 
240

0 to 240 sec. adjustment in 1sec steps

Pump Overrun Run 
Time

14:Pr

15

15 minutes

0 to 99

0 to 99 mins adjustment in 1min steps

Summary of Contents for BDR91













Reviews: