background image

Installation Guide

3

2) Installing the CM900 Wireless System

Please  follow  the  illustrations  and  information  below  in  sequence  to  install  the  Relay  Box  and  room 

thermostat correctly. For applications other than gas boilers, enabling special features and to see what 

other system options are available refer to section 

4) Installer Mode

.

2.1 Installing the Relay Box

1

The Relay Box is a RF device. For the 

best performance install in an open 

space. Leave at least 30cm distance 

from any metal objects including wall 

boxes and boiler housing.

Do not mount on metal wall boxes.

EMC compliance considerations

Keep  AC  mains  supply/load  cables 

separate from signal wiring.
Refer to Code of Practice standards 

EN61000-5-1 and -2 for guidance.

NOTE:

 The Relay Box contains 

no  user  serviceable  parts.  It 

should be opened and installed 

by qualified installer only.

WARNING:

  Electrostatic  sensi-

tive  device!  Do  not  touch  the 

circuit board.

NOTE:

 All wiring must be in accordance with IEE regulations

CAUTION:

  Observe  ambient  temperature  and  current  limits 

(see the Relay Box wiring label)

Burner (direct control)

Zone valve

Cooling device

2

3

4

< 7mm Ø

> 7mm Ø

a.

b.

6

5

1.5-2.5mm²

6mm max.

Combi boiler

230V

50-60Hz

<5A

BDR91

A-B:5(3)A

A-C:5(3)A

BDR91

A-B:5(3)A

A-C:5(3)A

230V

50-60Hz

<5A

V4043H

BDR91

A-B:5(3)A

A-C:5(3)A

230V

50-60Hz

<5A

BDR91

A-B:5(3)A

A-C:5(3)A

230V

50-60Hz

<5A

M

3.5

N

o

6

1

2

2

1

Summary of Contents for BDR91













Reviews: