background image

HAWK 8000 Controller 

Installation & 
Commissioning 
Instructions 

 

 
 

® U.S. Registered Trademark 
Copyright © 2018 Honeywell Inc.  •  All Rights Reserved 

 

EN1Z-1016GE51 R0218 

TABLE OF CONTENTS 

Safety Information --------------------------------------------------------------------------------------------------------------------------------------------- 2

 

General Safety Information -------------------------------------------------------------------------------------------------------------------------- 2

 

Construction --------------------------------------------------------------------------------------------------------------------------------------------- 2

 

Mounting Method --------------------------------------------------------------------------------------------------------------------------------------- 2

 

WEEE Directive ----------------------------------------------------------------------------------------------------------------------------------------- 2

 

End User License Agreement ------------------------------------------------------------------------------------------------------------------------------ 2

 

Model Description --------------------------------------------------------------------------------------------------------------------------------------------- 2

 

HAWK 8000 ---------------------------------------------------------------------------------------------------------------------------------------------- 2

 

Included in Shipment ---------------------------------------------------------------------------------------------------------------------------------- 2

 

Overview of Features ----------------------------------------------------------------------------------------------------------------------------------------- 3

 

Materials and Tools Required ----------------------------------------------------------------------------------------------------------------------- 4

 

Preparation ------------------------------------------------------------------------------------------------------------------------------------------------------- 4

 

Mounting ---------------------------------------------------------------------------------------------------------------------------------------------------------- 4

 

Environmental Requirements ----------------------------------------------------------------------------------------------------------------------- 4

 

Dimensions, Tab Mounting -------------------------------------------------------------------------------------------------------------------------- 4

 

Mounting on a DIN Rail ------------------------------------------------------------------------------------------------------------------------------- 5

 

Wiring ------------------------------------------------------------------------------------------------------------------------------------------------------ 5

 

Bus and Port Connections --------------------------------------------------------------------------------------------------------------------------- 6

 

Order Numbers------------------------------------------------------------------------------------------------------------------------------------------------ 11

 

Drivers ----------------------------------------------------------------------------------------------------------------------------------------------------------- 11

 

Included Drivers -------------------------------------------------------------------------------------------------------------------------------------- 11

 

Optional Drivers --------------------------------------------------------------------------------------------------------------------------------------- 11

 

Specifications ------------------------------------------------------------------------------------------------------------------------------------------------- 12

 

Power ---------------------------------------------------------------------------------------------------------------------------------------------------- 12

 

Environmental Specifications ---------------------------------------------------------------------------------------------------------------------- 12

 

Approvals, Certifications, etc. --------------------------------------------------------------------------------------------------------------------------- 12

 

Related Technical Literature ----------------------------------------------------------------------------------------------------------------------------- 12

 

 
 

Trademark Information

 

LON, L

ON

W

ORKS

, and Neuron are trademarks of Echelon 

Corporation registered in the United States and other 
countries. 
 

Summary of Contents for Centra Line CLNXHAW-5K













Reviews: