background image

COMFORTPOINT PROGRAMMABLE LON, VAV/UNITARY CONTROLLERS

62-0288—03

4

Mount Controller

NOTE: The controller may be wired before mounting to a 

panel or DIN rail.

Terminal blocks are used to make all wiring connections to the 

controller. Attach all wiring to the appropriate terminal blocks 

(see “Wiring” on page 6).

See Fig. 4 to Fig. 7 for panel mounting dimensions. See Fig. 8 

on page 5 for DIN rail mounting.

Fig. 4. Panel mounting — controller and actuator 

dimensions in inches (mm) for CP-VL6436AS only.

Fig. 5. Panel mounting — controller dimensions in inches 

(mm) for CP-UL1012S, CP-UL4024S, and CP-VL4024NS 

only (CP-UL4024S and CP-VL4024NS shown).

Fig. 6. Panel mounting — controller and actuator 

dimensions in inches (mm) for CP-VL0000AS and 

CP-VL4022AS only (CP-VL4022AS shown).

Fig. 7. Panel mounting — controller dimensions in inches (mm) for CP-UL6438S and CP-VL6438NS only.

1 2 3 4 5 6 7 8

1

0

9

2 3 4 5 6 7

1

1 1 1 1 1 1 1

1 2 3 4 5 6 7 8 0

9

2

2 2 2 2 2 2 2 2 3

3

1 2 3 4 5 6 7 8 0

9

3

3

3

3

3

3

3

3 4

5-3/4

(146)

10-5/16 (262)

NOTE:  CONTROLLER CAN BE MOUNTED IN ANY ORIENTATION.

PANEL MOUNTING HOLE

(4X) 3/16 IN. (4.5)

M28647

5-3/64

(128)

8-5/16 (211)

6-29/64 (164)

1-55/64 

(47)

6-17/64

(159)

7/16

(11)

DEPTH IS 

2-1/4 (57)

M28649

NOTE:  CONTROLLER CAN BE MOUNTED IN ANY ORIENTATION.

3/16 (4.5) PANEL MOUNTING HOLE (4X)

1 1 1 1 1 1 1 2 2 2 2 2

3 4 5 6 7 8 9 0 1 2 3 4

1 1 1 1 1 1 1 2 2 2 2 2

3 4 5 6 7 8 9 0 1 2 3 4

                           1 1

1 2 3 4 5 6 7 8 9 0 1 2

                           1 1

1 2 3 4 5 6 7 8 9 0 1 2

DEPTH IS 2-1/4 (57)

4-13/16 (122)

4-1/8 (105)

6-1/4

(159)

5-7/8

(149)

4-13/16 (122)

4-1/8 (105)

6-1/4

(159)

5-7/8

(149)

NOTE:  CONTROLLER CAN BE MOUNTED IN ANY ORIENTATION.

M28648

8-9/32

(211) 1-15/16

(49)

6-9/32

(159)

3/16 (4.5) PANEL

MOUNTING HOLE (4X)

27/32

(21)

4-1/8

(105)

6-1/4

(159)5-7/8

(149)

DEPTH IS 

2-1/4 (57)

1 2 3 4 5 6 7 8

  1 1 1 1 1 1 1 1 1 1 2

9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4 5 6 7 8 

2 3 4 5 6 7 8  0 

1  1 1 1 1 1 1 1  2 

1 2 3 4 5 6 7 8  0 

2 2 

2 2 2 2 2 2  3 

1 2 3 4 5 6 7 8  0 

3 3 

3 3 

3 4 

5-3/4 

(146) 

6-27/32 (174) 

NOTE:  CONTROLLER CAN BE MOUNTED IN ANY ORIENTATION. 

PANEL MOUNTING HOLE 

(4X) 29/64 IN. (12) 

M29168

5-3/64 

(128) 

6-29/64 (164) 

5-29/64 

(139) 

1 2 3 4 5 6 7 8 

2 3 4 5 6 7 8  0 

1  1 1 1 1 1 1 1  2 

1 2 3 4 5 6 7 8  0 

2 2 

2 2 2 2 2 2  3 

1 2 3 4 5 6 7 8  0 

3 3 

3 3 

3 4 

6-27/32 (174) 

5-3/64 

(128) 

6-29/64 (164) 

5-29/64 

(139) 

CP-VL6438NS

CP-UL6438S

DEPTH IS  

2-1/4 (57) 

Summary of Contents for CP-UL1012S









Reviews: