background image

Limited Warranty and Limitation Liability

BW Technologies LP (BW) warrants the product to be free from defects in material and workmanship under normal use and service for a period of two years, beginning on the date of shipment to the buyer. This 
warranty extends only to the sale of new and unused products to the original buyer. BW’s warranty obligation is limited, at BW’s option, to refund of the purchase price, repair or replacement of a defective 
product that is returned to a BW authorized service center within the warranty period. In no event shall BW’s liability hereunder exceed the purchase price actually paid by the buyer for the Product. 
This warranty does not include:

a) fuses, disposable batteries or the routine replacement of parts due to the normal wear and tear of the product arising from use;
b) any product which in BW’s opinion, has been misused, altered, neglected or damaged, by accident or abnormal conditions of operation, handling or use;
c) any damage or defects attributable to repair of the product by any person other than an authorized dealer, or the installation of unapproved parts on the product; or

The obligations set forth in this warranty are conditional on:

a) proper storage, installation, calibration, use, maintenance and compliance with the product manual instructions and any other applicable recommendations of BW;
b) the buyer promptly notifying BW of any defect and, if required, promptly making the product available for correction. No goods shall be returned to BW until receipt by the buyer of shipping instructions 

from BW; and

c) the right of BW to require that the buyer provide proof of purchase such as the original invoice, bill of sale or packing slip to establish that the product is within the warranty period.

THE

 

BUYER

 

AGREES

 

THAT

 

THIS

 

WARRANTY

 

IS

 

THE

 

BUYER

S

 

SOLE

 

AND

 

EXCLUSIVE

 

REMEDY

 

AND

 

IS

 

IN

 

LIEU

 

OF

 

ALL

 

OTHER

 

WARRANTIES

EXPRESS

 

OR

 

IMPLIED

INCLUDING

 

BUT

 

NOT

 

LIMITED

 

TO

 

ANY

 

IMPLIED

 

WARRANTY

 

OF

 

MERCHANTABILITY

 

OR

 

FITNESS

 

FOR

 

A

 

PARTICULAR

 

PURPOSE

BW

 

SHALL

 

NOT

 

BE

 

LIABLE

 

FOR

 

ANY

 

SPECIAL

INDIRECT

INCIDENTAL

 

OR

 

CONSEQUENTIAL

 

DAMAGES

 

OR

 

LOSSES

INCLUDING

 

LOSS

 

OF

 

DATA

WHETHER

 

ARISING

 

FROM

 

BREACH

 

OF

 

WARRANTY

 

OR

 

BASED

 

ON

 

CONTRACT

TORT

 

OR

 

RELIANCE

 

OR

 

ANY

 

OTHER

 

THEORY

.

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not 
apply to every buyer. If any provision of this warranty is held invalid or unenforceable by a court of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

Contacting BW Technologies by Honeywell

Corporate Headquarters

BW Technologies by Honeywell

2840 2nd Ave. SE

Calgary, AB

Canada  T2A 7X9

Tel:

+1.403.248.9226

Toll-free: 1.800.663.4164

Fax:

+1.403.573.3708

United States

BW Technologies by Honeywell

405 Barclay Blvd.

Lincolnshire, IL

USA  60069

Tel:

+1.847.955.8200

Toll-free: 1.800.538.0363

Fax:

+1.847.955.8210

Europe

BW Technologies by Honeywell

4 Stinsford Road

Nuffield Industrial Estate

Poole, Dorset

United Kingdom  BH17 0RZ

Tel: +44 (0) 1295.700.300

Fax: +44 (0) 1295.700.301

Asia Pacific

Honeywell

 

Analytics

 

Asia

 

Pacific

#701

 

Kolon

 

Science

 

Valley

 

(1)

43

 

Digital

Ro,

 

34

Gil

 

Guro

Gu,

 

Seoul,

  

152

729

Korea
Tel:

 

+82

 

(0)2

 

6909

 

0300

Fax:

 

+82

 

(0)2

 

2025

 

0388

Email:

analytics.ap@honeywell.com

Email

info@gasmonitors.com

Web

www.gasmonitors.com

Summary of Contents for D4-PF-1





















Reviews: