Honeywell DHC 23 Operating Instructions Manual Download

Page: 29 / 31

DHC 23

TECHNICAL DATA

■■

Technical data

Control system

Microprocessor control with analogue operation

Type designation

DHC 23

Order designation

DHC 23-1:

One heating circuit, optionally one domestic hot water circuit

DHC 23-2:

One mixed heating circuit, optionally one unmixed heating circuit,
or domestic hot water control

DHC 23-3:

Nordic standard domestic hot water circuit with fast response
heat exchanger, optionally one heating circuit.

Construction

Digital controller in impact-proof plastic housing, plug-in unit base with screw
terminals

Version

Corresponding to DIN 32 729
Corresponding to draft AGFW Memorandum "Requirements on outside temperature
compensated control devices"

Controller type

PI controller

Default switching times

Heating times:

daily 6.00 until 22.00

Domestic hot water availability:

daily 6.00 until 22.00

Automatic preventive maintenance

Heating circuit pump:

daily 10.00, 1 min.

operation

Summer/winter time changeover

Start of summer time:

last Sunday in March, 2.00 (1 hour forwards)

Start of winter time:

last Sunday in October, 3.00 h (1 hour back)

Supply voltage

230 V AC + 6 % ... -15 % 50...60 Hz

Power consumption

5 W

Data protection

Individual data protection (eg. during power failure) by an exchangeable battery for up
2 years continuously, thereafter a maximum of 48 hours per year (at 20°C)

Protection standard

IP 30 according to EN 60529

Protection class

II according to EN 60730-1

Radio interference

conformity

according to EN 50 081-1 and EN 50 082-1

Dimensions

192 x 96 mm (W x H according to DIN 43700) x 98 mm (D)

Control panel cut-out

186+1.1 x 92+0.8 mm

Weight

approx. 950 g without packaging

Mounting

Wall mounting or control panel front installation with control panel installation set ER 9

Terminals

Screw terminals, max. cable cross-section 1.5 mm

Storage temperature

-20°C...+65°C

Operating temperature

0...40°C

Relativet humidity

5...70 %

10878_BDA_DHC23_engl_neu 06.09.1999 13:51 Uhr Seite 29

Summary of Contents for DHC 23
































Search results

Summary of Contents for DHC 23

Reviews:

Related manuals for DHC 23

Brands by name

Popular brands

Honeywell DHC 23, Operating Instructions Manual

Search results

Summary of Contents for DHC 23

Reviews:

Related manuals for DHC 23

Brands by name

Popular brands