Honeywell Fire-Lite Alarms ES-200X Manual Download

Page: 80 / 168

ES-200X Series Manual —

P/N LS10131-000FL-E:C 7/25/2018

Programming

Master Programming Level

MNS Override

Pressing

while viewing System Setup Screen #3 will allow the programmer to configure the system for

use with the Mass Notification System (ECC-50/100 panel). Each press of the

key will toggle the display

between

MNS Override No

and

MNS Override Yes

. When

MNS Override No

is selected, the ECC-50/100

panel does not have permission to override the FACP. When

MNS Override Yes

is selected, the ECC-50/100

panel will override the FACP, taking control of its NACs and control modules during a mass notification
event. Refer to the

ECC-50/100 Manual

for more information. When the

Canadian Option

is set to

, the

MNS Override

feature will become unavailable.

Auxiliary Power

Two Special Application 24 VDC power outputs are available at TB11 on the main circuit board. Pressing 3
while viewing System Setup Screen #4 displays the following:

Select the desired output. The following screen will be displayed.

Each output can be programmed as resettable or non-resettable power. Non-resettable power is suitable for powering annunciators while
resettable power is suitable for powering smoke detectors. Each press of the

key will cause the display to toggle between

Resettable

Yes

and

Resettable No.

In addition, Aux 1 can be programmed for Class A wiring. If Aux 1 is to be wired for Class A, press

. Each press of the

key will cause

the display to toggle between

Class A Yes

and

Class A No.

Trouble Reminder

The Trouble Reminder features causes the control panel piezo to sound a reminder ‘beep’ for alarms and
troubles, after the panel has been silenced. Refer to “Trouble Reminder” on page 71, for a detailed descrip-
tion of this feature. Pressing

while viewing System Setup Screen #4 will cause the display to toggle to

Trouble Rem 4

Trouble Rem 24

, which enables this feature for resound at either 4 or 24 hours, respec-

tively. Each press of the

key will cause the display to toggle between

Trouble Rem 4

Trouble Rem 24

Refer to the table on page 49 for permissible settings.

Language

The language option is used to change the text on the panel display to either English or French. Pressing the

key will cause the display to offer a choice of

1=English

and

French.

Charger Enable

If using an external battery charger, the FACP battery charger must first be disabled. Pressing

while view-

ing System Setup Screen #5 will cause the display to toggle to

Charger Enab No

, which will allow the use

of an external battery charger. Each press of the

key will cause the display to toggle between

Charger

Enab Yes

and

Charger Enab No

4XTMF Supervision

If a 4XTMF Transmitter Module is installed in the system, supervision must enabled in user programming.
Pressing

while viewing System Setup Screen #5 will cause the display to toggle to

4XTM Supv Enab. Yes

which means there is a 4XTMF installed. Each press of the

key will cause the display to toggle between

4XTM Supv Enab. No

and

4XTM Supv Enab. Yes

. Refer to the table on page 49 for permissible settings.

Remote Sync Enable

Synchronization is a feature that controls the activation of notification appliances in such a way that all
devices will turn on and off at exactly the same time. Refer to Section 2.5, “Remote Synchronization Out-
put”, on page 28 for more information. To enable remote synchronization, press the

key while viewing

System Setup Screen #5. Each press of the key will toggle the screen between

Rem Sync Enab Yes

and

Rem

Sync Enab No

SYSTEM SETUP

1=CANADIAN OPT. OFF

2=WATERFLOW SIL. NO

3=MNS OVERRIDE NO

System Setup Screen #3

SYSTEM SETUP