162
Xenon/Granit User Guide
•
When setting up for specific symbologies (as opposed to all symbologies), the
specific symbology ID value counts as an added prefix or suffix character.
•
The maximum size of a prefix or suffix configuration is 200 characters, which
includes header information.
Add a Prefix or Suffix:
Step 1.
Scan the
Add Prefix
or
Add Suffix
symbol (
).
Step 2.
Determine the 2 digit hex value from the
on page A-339) for the symbology to which you want to apply the prefix
or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”.
Step 3.
Scan the 2 hex digits from the
9, 9
for all symbologies.
To add the Code I.D., scan
5, C, 8, 0
.
To add the AIM I.D., scan
5, C, 8, 1
.
To add the serial number, scan
5, C, 8, 8
.
To add a backslash (\), scan
5, C, 5, C
.
Note:
When adding a backslash (\), you must scan 5C twice – once to create the leading
backslash and then to create the backslash itself.
Step 4.
Repeat Steps 2 and 3 for every prefix or suffix character.
Step 5.
Scan
Save
to exit and save, or scan
Discard
to exit without saving.
Repeat the steps above to add a prefix or suffix for another symbology.
Example: Add a Tab Suffix to All Symbologies
Step 1.
Scan
Add Suffix
.
Step 2.
Scan
9, 9
from the
beginning on page 353 to apply
this suffix to all symbologies.
Step 3.
Scan
0, 9
from the
corresponds with the hex value for a horizontal tab, shown in the
Conversion Chart (Code Page 1252),
Step 4.
Scan
Save
, or scan
Discard
to exit without saving.
Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology.
If you have been entering prefixes and suffixes for single symbologies, you can use
Clear One Prefix
(
Suffix
) to delete a specific character from a symbology. When
you
Clear All Prefixes
(
Suffixes
), all the prefixes or suffixes for a symbology are
deleted.
Summary of Contents for Granit 1910i
