Honeywell GW-1000-WE Mounting Instructions Download

Page: 6 / 6

GW-1000-WE / GW-1000-NWE GATEWAY

® U.S. Registered Trademark

31-00425 | Rev.10-20

Part Number: 32348979-001

Honeywell Building Solutions

Honeywell
715 Peachtree Street NE
Atlanta, GA 30308
customer.honeywell.com
buildingcontrols.honeywell.com

Removing the Gateway from the Wall/Panel

Remove the Extended Terminal Covers if applicable (see the Removing the Extended Terminal Cover section).

Disconnect all the communication and power supply terminals from the Gateway.

Disconnect the antenna by turning the antenna terminal nut anticlockwise.

Unscrew the bottom side screws first by using a screwdriver.

Hold the Gateway with one hand and unscrew the top side screws by using a screwdriver.

DIMENSIONS

122.4 mm

4.819"

106.7 mm

4.207"

59 mm

(2.323")

110 mm
(4.331")

45 mm

(1.772")

52 mm

(2.047")

135 mm

(5.315")

145.8 mm

(5.744")

Summary of Contents for GW-1000-WE







Search results

Summary of Contents for GW-1000-WE

Reviews:

Related manuals for GW-1000-WE

Brands by name

Popular brands

Honeywell GW-1000-WE, Mounting Instructions

Search results

Summary of Contents for GW-1000-WE

Reviews:

Related manuals for GW-1000-WE

Brands by name

Popular brands