Honeywell KT 74 Pilot'S Manual Download

Page: 11 / 17

KT 74 Pilot's Guide

D201308000036

Operation

Rev 0 Dec 2013

Page-1-5

Honeywell International Inc. Do not copy without express permission of Honeywell

1.5

PUSH BUTTONS

Figure 1-4: Push Buttons

IDENT

Press the

IDENT

button when ATC instructs you to

“Ident” or “Squawk Ident”. This activates the SPI pulse in

the transponder replies for 18 seconds.

IDENT

will

appear in the display.

VFR

Pressing the

VFR

button sets the transponder to the pre-

programmed VFR code. Pressing the button again

restores the previous squawk code.
Pressing the

VFR

button while in Flight ID editing mode

changes the Flight ID to the pre-programmed ID set up

during configuration of the transponder.

FUNC

Pressing the

FUNC

button provides access to the flight

timer, stopwatch, Flight ID entry, ADS-B monitor

(depending on installation) and altitude monitor function.

See section 1.6 below.

ENT

The ENT button confirms selection or presented options.

0-7

The numeric buttons are used to change the squawk

code and as part of the data entry selections.

Summary of Contents for KT 74


















Search results

Summary of Contents for KT 74

Reviews:

Related manuals for KT 74

Brands by name

Popular brands

Honeywell KT 74, Pilot'S Manual

Search results

Summary of Contents for KT 74

Reviews:

Related manuals for KT 74

Brands by name

Popular brands