LYNX Touch Installation and Setup Guide
- 15 -
Installing Wireless Zones
5800 Series Transmitter Loop Numbers
(Refer to this information when programming transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop
designations.
LOOP 1
5806/5806W3/5807
5808/5808LST/5808W3
ENROLL AS "RF"
LOOP 1
LOOP 1
5809
ENROLL AS "RF"
5 8 1 8
ENROLL AS "RF"
LOOP 1
LOOP 1
LOOPS
1 - 3
LOOP 1
LOOP 1
LOOP 1
LOOP 1
5814
ENROLL
AS "RF"
5800-002-V1
LOOP 1
(MOTION)
5897
ENROLL AS "RF"
5 8 9 0 / 5 8 9 0 P I
ENROLL AS "RF"
LOOP 1
LOOP 1
5 8 0 2 M N
ENROLL AS
"UR" OR "RF"
5 8 0 5 - 6
ENROLL AS "BR"
5 8 0 4 B D / 5 8 0 4 B DV
ENROLL AS "BR"
PROGRAM HOUSE ID
LOOP 4
LOOP
3
LOOP 1
LOOP 2
•
•
••
•
•
••
•
•
•
• •
• •
•
•••
5804/5804E
ENROLL AS "BR"
5 8 1 6 T E M P
ENROLL AS "RF"
5 8 1 7
ENROLL AS "RF"
LOOP 2
(AUX.
CENTER)
LOOP 1
(PRIMARY)
LOOP 3
(AUX.
RIGHT)
5 8 2 2 T
ENROLL AS "RF"
5 8 7 7
5 8 1 6 M N
ENROLL AS "RF"
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
LOOP 2
(REED)
LOOP 3
(TERMINALS)
5 8 2 8 / 5 8 2 8 V
P RO G R A M
HOUSE ID
5 8 2 1
ENROLL AS "RF"
5 8 2 0 L
ENROLL AS "RF"
5 8 1 9 S ( W H S & B R S )
ENROLL AS "RF"
LOOP 1
(INTERNAL
SHOCK
SENSOR
LOOP 2
(REED)
5 8 1 9
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 3
(TERMINALS)
LOOP 1
(TERMINALS)
5 8 0 0 WAV E
P RO G R A M
H O U S E I D
5 8 0 0 P I R - O D
E N R O L L A S " R F "
5 8 0 0 P I R /
5 8 0 0 P I R - C O M
E N R O L L A S " R F "
5 8 1 1
E N R O L L A S " R F "
5 8 0 0 P I R - R E S
E N R O L L A S " R F "
5 8 0 0 M i c r a
E N R O L L A S " R F "
5 8 0 0 C O
E N R O L L A S " R F "
5 8 0 0 S S 1
E N RO L L A S " R F "
5 8 0 0 R L
S E T
H O U S E I D
LOOP 1
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
LOOP 1
(HIGH
SECURITY)
LOOP 2
(STANDARD
SECURITY)
LOOP 3 (TILT MODE)
LOOP 4 (TAMPER)
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5834-4
ENROLL AS "BR"
5 8 9 4 P I
ENROLL AS "RF"
5 8 0 2 M N 2
ENROLL AS
"UR" OR "RF"
LOOP
1
LOOP
1
LOOP
1
LOOP
1
5 8 7 8
ENROLL AS "BR"
5870API
ENROLL AS "RF"
5 8 5 3
ENROLL AS "RF"
ARMED
READY
MESSAGE
MIC
LOOP 1
(LOW SENSITIVITY)
LOOP 2
(HIGH SENSITIVITY)
5 8 9 8
ENROLL AS "RF"
LOOP 4
LOOP 1
LOOP 2
LOOP 3
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 3
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
3
AW
AY
ST
AY
1
2
4
OFF
ON
4
3
2
1
OFF
ON
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 1
SERIAL #2
LOOP 2
SERIAL #2
LOOP 3
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 3
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
SERIAL #2 - LOOP 1 = ON + 4 BUTTONS
LOOP 4 = 3 + 4 BUTTONS
SERIAL #2
LOOP 4
LOOP 3
5 8 1 6
ENROLL AS "RF"
LOOP 1
(TEMP
SENSOR)
LOOP 1
(TERMINALS)
LOOP 2
(REED)
Notes: (1)
The 5806W3 smoke detector must be used in SIA applications.
(2) Button type (BR) devices send only fault and low battery signals; no restore or check-in signals.
Supervised RF (RF) devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised RF (UR) devices send periodic check-in signals, faults, restore and low battery signals but the control does not
supervise the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
(4) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Go/No-Go Test Mode. Refer
to the transmitter’s Installation Instruction for complete details. The system will confirm the enrollment of the encrypted device
by beeping two times
UL
The
5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5814, 5816TEMP, 5819, 5819S(WHS & BRS), and
5828/5828V wireless transmitters
have not been evaluated by UL
.
