background image

SERIES 61 AND SERIES 62 MODUTROL IV™ MOTORS

3

63-2188—4

Fig. 1. Series 61 and 62 Modutrol IV Motor mounting dimensions in in. (mm).

Electrical Ratings: 

See Table 2.

Table 2. Series 61 and 62 Modutrol IV Motor 

Power Consumption Ratings.

Auxiliary Switch Ratings: 

See Table 3.

Table 3. Auxiliary Switch Ratings.

a

40 VA pilot duty, 120/240 Vac on opposite contact.

Control Inputs:

Floating three-wire (Series 60): drive open, hold, drive closed.

Series 62 models include an internal, electrically isolated 

feedback potentiometer that provides shaft position 

indication.

M17089BB

4-7/8

(124)

5-1/2

(140)

13/16

(20)

4-1/16 (103)

1/4

(7)

1-1/2 (37)

4-1/16 (103)

4-1/16 (103)

WIRING

BOX

MOTOR

AUXILARY

END

POWER

END

ADAPTER

BRACKET

2-9/16

(66)

5-3/8

(137)

6-7/16

(164)

9/16 (15)

3/4

(19)

TOP VIEW OF BRACKET 

TOP VIEW

4-5/8

(116)

4-1/4

(107)

2-5/16

(58)

11/16

(17)

4-7/8 (124)

5-9/16 (141)

1/4 (7)

5-13/16

(148)

2

POWER END

1

3

4

5

1-1/2 (37)

3/4

(19)

SPRING RETURN MODEL SHOWN

SOME MODELS DO NOT HAVE AN AUXILIARY 

SHAFT. ALL OTHER DIMENSIONS ARE THE SAME. 

FOR HIGH TORQUE (60 LB-IN.) SPRING RETURN 

MODELS 8-3/4 (222); FOR LOW TORQUE (25 LB-IN.) 

SPRING RETURN MODELS 8-1/4 (210); 

NON-SPRING RETURN MODELS 7-5/16 (185).

FOR HIGH TORQUE (60 LB-IN.) SPRING 

RETURN MODELS (SHOWN).

FOR LOW TORQUE (25 LB-IN.) SPRING 

RETURN MODELS.

FOR NON-SPRING RETURN MODELS.

1

2

3

4

5

Internal 

Transformer

Voltage at 

50/60 Hz

Power Consumption

Non-Spring 

Return

Spring 

Return

(VA)

(W)

(VA)

(W)

No

24

17

15

21

20

Yes

24

26

20

30

25

120

26

20

30

25

208

26

20

30

25

240

27

20

34

25

Single Contact 

Rating

a

120V (in Amps)

240V (in Amps)

Full Load

7.2

3.6

Locked Rotor

43.2

21.6

Summary of Contents for Modutrol IV Series 61













Reviews: