Honeywell NOTIFIER ACS Series Manual Download

Page: 12 / 60

ACS Manual —

P/N 15842:

5/4/2022

Product Overview

ACM-32A Series

3.3.2 Expander Modules

AEM-16AT

The Annunciator Expander Module-16AT expands the ACM-16AT series by 16 system points. The AEM-16AT series is identi-

cal in size and in frontal appearance to the ACM-16AT series. One to three of these expander modules can be supported by an ACM-16AT,
ACM-16ATG, or ACM-ATY, to a maximum of 64 system points. Height = 8.375" (21.27 cm), Width = 4.375" (11.11 cm).

AEM-16ATY

Same as the AEM-16AT but all LEDs are yellow (yellow On/Alarm and yellow Trouble).

AEM-16ATG

Same as the AEM-16AT, but On/Alarm LEDs are green (green On/Alarm and yellow Trouble).

3.4 ACM-32A Series

3.4.1 Control Modules

ACM-32A

The Annunciator Control Module-32A contains 32 red point active LEDs, a system trouble LED,

an On-line/Power LED, and a local piezo sounder with a silence/acknowledge switch for audible indication of
alarm and trouble conditions at each annunciator. Height = 8.375" (21.27 cm), Width = 4.375" (11.11 cm). In
Canada this module must be used to annunciate the fire alarm input points/zones only.

ACM-32AG

Same as the ACM-32A, but On/Alarm LEDs are green (green On/Alarm and yellow Trouble). In

Canada this module may be used to annunciate notification appliance circuit activation or other output cir-
cuit/zone activation.

ACM-32AY

Same as the ACM-32A but with all LEDs yellow (yellow On/Alarm and yellow Trouble). In Can-

ada this module must be used to annunciate supervisory and burglary signals from associated points/zones.

3.4.2 Expander Modules

AEM-32A

The Annunciator Expander Module-32A expands the ACM-32A series by 32 system points. The AEM-32A (with red LEDs) is

identical in frontal appearance to the ACM-32A. One expander module can be supported by an ACM-32A, ACM-32AG, or ACM-32AY,
providing a maximum of 64 points. Height = 8.375" (21.27 cm), Width = 4.375" (11.11 cm).

AEM-32Y

Same as the AEM-32A but with all LEDs yellow (yellow On/Alarm and yellow Trouble).

AEM-32G

Same as the AEM-32A, but On/Alarm LEDs are green (green On/Alarm and yellow Trouble).

3.5 Cabinet & Panel Hardware

3.5.1 Surface-Mount Backboxes

These backboxes provide a surface-mount enclosure for remote mounting annunciators. Knockouts are provided for use
with 1/2" conduit. Dimensions are provided in Table 3.1.

ABS-1B

Mounts one annunciator directly to the ABS-1B without a dress plate. This backbox will not support the installa-

tion of the Annunciator Keyswitch or the Annunciator Phone Jack for Firefighters' Telephone.

ABS-2B

Mounts two annunciators directly to the ABS-2B without a dress plate. This backbox will not support the instal-

lation of the Annunciator Keyswitch or the Annunciator Phone Jack.

ABS-2D, ABS-2DR

Mounts two annunciators. This surface box can also be mounted semi-flush. This backbox will not

support the installation of the Annunciator Keyswitch or the Annunciator Phone Jack for Firefighters' Telephone.

ABS-4D, ABS-4DR

Mounts four annunciators, or two annunciators to the right of the NCA. This surface box can also be

mounted semi-flush. This backbox will not support the installation of the Annunciator Keyswitch or the Annunciator
Phone Jack for Firefighters' Telephone.

ABS-1TB

Mounts one annunciator. Unlike the ABS-1B and ABS-2B, the ABS-1TB has an increased depth that allows mounting of the

Annunciator Phone Jack for Firefighters' Telephone and Annunciator Keyswitch.

NOTE:

The AEM-16AT series cannot be used to expand the ACM-24AT, ACM-48A, or ACM-32A series. Expander LED colors need not match

the control module LED colors for the expander to operate.

1. In Canada the color red must be used to indicate active alarm inputs. Yellow indicates supervisory, burglary or trouble signals.

Green indicates the presence of power, or an activated output.

-f

NOTE:

The AEM-32A cannot be used to expand the ACM-24AT, ACM-48A, or ACM-32A series. Expander LED colors need not match the

control module LED colors for the expander to operate.