Honeywell NOTIFIER NFW-50X Manual Download

Page: 76 / 158

NFW-50X Manual —

P/N LS10129-001NF-E:C 7/25/2018

Programming

Master Programming Level

•

The F1 function key is automatically configured to perform a manual alarm signal activation when pressed.

•

The F2 function key is automatically configured to perform a two-stage bypass when pressed.

•

If NACs are set up for two-stage operation, the Silence Inhibit timer is automatically enabled and is fixed at 5 minutes.

•

AlarmNet supervision settings are fixed at 3 minutes and cannot be changed regardless of supervision programming selection.

Waterflow Silenceable

Pressing

while viewing System Setup Screen #3 will allow the programmer to configure the system for

silenceable on nonsilenceable waterflow circuits. Each press of the

key will toggle the display between

Waterflow Sil. No

and

Waterflow Sil. Yes

. When

Waterflow Sil. No

is selected, all output devices associated

with a waterflow type input device, will be nonsilenceable. When

Waterflow Sil. Yes

is selected, all output

devices associated with a waterflow type input device, will be silenceable.

Auxiliary Power

A Special Application 24 VDC power output is available at TB11 on the main circuit board. Pressing

while viewing System Setup Screen #4 displays the following:

Select the AUX 1 output. The following screen will be displayed.

Aux 1 can be programmed for Class A wiring. If Aux 1 is to be wired for Class A, press

. Each press of the

key will cause the display

to toggle between

Class A Yes

and

Class A No.

In addition, the aux power output can be programmed as resettable or non-resettable power. Non-resettable power is suitable for power-
ing annunciators while resettable power is suitable for powering smoke detectors. Each press of the

key will cause the display to toggle

between

Resettable Yes

and

Resettable No.

Trouble Reminder

The Trouble Reminder features causes the control panel piezo to sound a reminder ‘beep’ for alarms and
troubles, after the panel has been silenced. Refer to “Trouble Reminder” on page 68, for a detailed descrip-
tion of this feature. Pressing

while viewing System Setup Screen #4 will cause the display to toggle to

Trouble Rem 4

Trouble Rem 24

, which enables this feature for resound at either 4 or 24 hours, respec-

tively. Each press of the

key will cause the display to toggle between

Trouble Rem 4

Trouble Rem 24

Refer to the table on page 46 for permissible settings.

Language

The language option is used to change the text on the panel display to either English or French. Pressing the

key will cause the display to offer a choice of

1=English

and

French.

Charger Enable

If using an external battery charger, the FACP battery charger must first be disabled. Pressing

while view-

ing System Setup Screen #5 will cause the display to toggle to

Charger Enab No

, which will allow the use

of an external battery charger. Each press of the

key will cause the display to toggle between

Charger

Enab. No

and

Charger Enab. Yes

4XTM Supervision

If a 4XTM Transmitter Module is installed in the system, supervision must enabled in user programming.
Pressing

while viewing System Setup Screen #5 will cause the display to toggle to

4XTM Supv Enab. Yes

which means there is a 4XTM installed. Each press of the

key will cause the display to toggle between

4XTM Supv Enab. No

and

4XTM Supv Enab. Yes

. Refer to the table on page 46 for permissible settings.

Remote Sync Enable

Synchronization is a feature that controls the activation of notification appliances in such a way that all
devices will turn on and off at exactly the same time. Refer to Section 2.5, “Remote Synchronization Out-
put”, on page 26 for more information. To enable remote synchronization, press the

key while viewing

System Setup Screen #5. Each press of the key will toggle the screen between

Rem Sync Enab Yes

and

Rem

Sync Enab No

SYSTEM SETUP

1=CANADIAN OPT. OFF

2=WATERFLOW SIL. NO

System Setup Screen #3

SYSTEM SETUP

1=AUX POWER