background image

PRODUCT DATA

71-2429-06

L404F,T,V
PressureTrol

®

 Controllers

APPLICATION

L404F PressureTrol

®

 Controllers provide operating control 

with automatic limit protection for pressure systems of up to 

2070 kPa, or 300 psi.

L404T,V PressureTrol

®

 Controllers are for use on oil burner 

systems for pressures up to 1035 kPa or 150 psi.

FEATURES

• Models available in a series of control ranges, and 

pressure scales in kPa and psi.

• All models automatically reset and have an adjustable 

differential.

• Models have snap switch to open or close a circuit on 

a pressure rise.

• Case has a clear plastic cover so setpoints can be 

observed.

• 1/4 inch—18 NPT connection for pipe on diaphragm 

assembly.

• Ground screw terminal.
L404F:

• Controllers may be used with steam, air, or 

noncombustible gases, or fluids noncorrosive to the 

pressure sensing element.

L404T:

• High pressure limits, break a circuit on oil pressure 

rise above setpoint.

L404V:

• Low pressure limits, makes a circuit on oil pressure 

rise above setpoint.

Contents

Application ........................................................................

1

Features ...........................................................................

1

Specifications ...................................................................

2

Ordering Information  ........................................................

2

Installation ........................................................................

4

Settings and Adjustments .................................................

6

Checkout ..........................................................................

7

Summary of Contents for PRESSURETROL L404F









Reviews: