background image

PRODUCT DATA

65-0268-1

® U.S. Registered Trademark
Copyright © 2002 Honeywell •  All Rights Reserved 

P7810A-D

Pressuretrol® Controller

APPLICATION

The P7810 Pressuretrol® Controller is a line voltage pressure 

controller for pressure systems up to 300 psi (2069 kPa). Four 

models are available:

• P7810A—On/Off Control

• P7810B—On/Off Control with 4 to 20 mA modulation.

• P7810C—On/Off Control, High Limit and 4 to 20 mA 

modulation.

• P7810D—On/Off Control with High Limit.

FEATURES

• Use only with steam, air or noncombustible gases that 

do not corrode the pressure sensing element.

• Models available with on-off control function, on-off 

control and modulate, high limit and modulate, and 

on-off control and safety high limit functions.

• Models available in 15, 150 and 300 psi (103, 1034 and 

2069 kPa) maximum setpoints.

• LED indicators show power, call for heat function and 

lockout status.

• Clear cover allows setpoint and differential to be read, 

but not adjusted, without opening cover, (Cover 

optional for P7810A,B models.)

• Manual reset possible without opening cover.
• Electronic maximum fixed stop limit.

P7810A, B

P7810C, D

Contents

Application ........................................................................

1

Features ...........................................................................

1

Specifications ...................................................................

2

Ordering Information  ........................................................

2

Installation ........................................................................

3

Wiring ...............................................................................

5

Operation ..........................................................................

7

Checkout .......................................................................... 11

Troubleshooting ................................................................ 12

Service Information  .......................................................... 12

Summary of Contents for Pressuretrol P7810A













Reviews: