background image

P7810C,D PRESSURETROL

®

 CONTROLLER

65-0235—1

2

ORDERING INFORMATION

When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the
TRADELINE® Catalog or price sheets for complete ordering number.

If you have additional questions, need further information, or would like to comment on our products or services, please contact:

1.

Your local Home and Building Control Sales Office (check white pages of your phone directory).

2. Home and Building Control Customer 

Relations

Honeywell, 1

8

85 Douglas Drive North

Minneapolis, Minnesota 55422-4386

  

In Canada—Honeywell Limited/Honeywell Limitée, 

35 Dynamic Drive, Scarborough

, Ontario M

1V 4Z9

.

International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.

Maximum Setpoint (psig) Pressure Range (psig)

Overpressure (psig)

Burst Pressure (psig)

Differential (psig)

15

0 to 15

22.5

60

2 to 10

150

0 to 150

225

600

5 to 20

300

0 to 300

450

1200

15 to 50

SPECIFICATIONS

Models:

P7810C Pressuretrol® Controller with on/off control/

modulate and safety high limit.

P7810D Pressuretrol® Controller with on/off control and

safety high limit.

Electrical Ratings:

Power Input: 120 Vac (+10%/-15%), 50/60 Hz.
Power Consumption:

Sensor Material:
304 stainless steel.

Case Material:
Plastic.

Electrical Terminations:
Screw terminals.

Operating Temperature  Range:
32

°

F to +150

°

F (0

°

C to +65

°

C).

Storage Temperature:
-20

°

F to 150

°

F (-29

°

C to 65

°

C).

Accuracy:

±

4.0 percent full scale output operating range, over operating

temperature.

Humidity:
5 to 95 percent relative humidity, noncondensing.

Vibration:
1/2G continuous maximum vibration.

Dimensions:
See Fig. 1.

Mounting Position:
Upright, see Fig. 2.

Device Weight:
2.0 lb, 8 oz (1.15 kg).

Approvals:

Underwriters Laboratories Inc. Listed: File MP466.
Canadian Standards Association Listed: Pending.
Factory Mutual Approved: Listed: J.I. 2D3A6AF.
CSD-1 AFB (Control Safety Devices, Automatic Fired

Boilers): Acceptable.

FCC Class B, computing devices, part 15.

Switch Contact Ratings:

Pressure Ratings:

Accessories:
209731A Siphon Loop with 1/2 in. NPT threads.
4074EWD Mounting Bracket with six screws.
4074EDC or EED Bag Assembly to interface 4 to 20 mA with
Series 90 Firing Rate Motor.

Replacement Parts:
4074EVP Door Wrench.
4074EWC Door Assembly with captive screw and adjusting
wrench.

120 Vac

Rating

50 Hz

60 Hz

Watts

3.6

3.3

VA

4.7

4.0

Contact Rating (120 Vac)

10A resistive

9.8A Full Load

58.8A Locked Rotor

Summary of Contents for Pressuretrol P7810C









Reviews: