Honeywell SH-771E, User Instructions

4

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS 

Read all instructions before operating this quick
heater. Keep these instructions.

1.

Operate the quick heater out of the reach of
children. 

2.

Do not operate the quick heater outdoors. 

3.

Place the quick heater on a level, firm surface.
Make sure it is in a stable position, so that it
cannot fall over or fall down. 

Only operate 

the quick heater in an upright position.

4.

Unravel the Supply Cord (15) before use. 
Failure to do so could cause overheating 
and possible fire hazard. 

5.

Do not use an extension cord or a         
solid-state speed-control device. Doing so 
could cause overheating, fire hazard or 
electric shock. 

6.

Only connect the quick heater to a          
single-phase AC supply to the voltage 
shown on the rating plate. 

7.

Always disconnect cord at wall plug before 
removing the quick heater, touching,       
moving, cleaning or when not in use.       
Do not pull on Supply Cord (15) when     
disconnecting it. 

8.

Do 

not

operate the quick heater in rooms 

with explosive gases or while using       
inflammable solvents, varnish, glue etc.

9.

Do not place the quick heater directly below
a socket. 

10.

Do not use this quick heater in the          
immediate surroundings of a bath, shower 
or swimming pool. 

11.

This quick heater must 

not

be used in any 

kind of vehicle (e.g. builder’s huts, lifts, 
camper vans, motor vehicles, cars) and     
similar, self-contained space. 

12.

If wall-mounted do not fix to combustible 
material such as wooden, synthetic or     
plastic surfaces.

13.

Caution: The Air Outlet (6) gets hot during 
operation (above 80 °C or 175 °F). Keep 
combustible material such as furniture,   
cushions, bedding, paper, curtains, clothes 
at least 1 meter away from the quick heater.

14.

Keep the quick heater clean. Make sure that
the Air Inlet (14) and Outlet (6) are       
unobstructed. Do 

not 

allow 

any 

objects to 

enter into the Air Inlet (14) and Outlet (6). 
Do 

not

cover the quick heater. This could 

cause overheating, fire hazard or electric 
shock.

15.

Do not immerse the quick heater in water or
other liquids and do not pour water or other
liquids over the appliance or into the Air 
Inlet (14) or Outlet (6). 

16.

Clean the quick heater regularly and follow 
the “Cleaning Instructions”.

17.

If the Supply Cord (15) of the quick heater 
is damaged it must be repaired by a repair 
shop appointed by the manufacturer, as 
special purpose tools are required. 

18.

Do not operate the quick heater if it is  
damaged, faulty or is not working properly.
Disconnect it from the electricity supply. 

PARTS IDENTIFICATION

1.

Opening for Wall-Mounting Support

2.

Wall-Mounting Support

3.

Installation Zones

4.

Safety Distances   

5.

Variable Air Flow Range

6.

Air Outlet     

7.

Power Switch 

8.

Pilot Light 

9.

Thermostat Switch 

10.

Off-Position 

11.

Warm Air 1000 W  Low Speed 

12.

Warm Air 1200 W  Low Speed 

13.

Hot Air 2000 W  High Speed 

14.

Air Inlet 

15.

Supply Cord with plug 

16.

Cord Storage  

17.

Room Temperature approx. 5 °C

18.

Room Temperature approx. 30 °C

OPERATION 

First Time Use 
1.

Read all instructions before using the quick 
heater. 

2.

Unpack the quick heater and the Supply 
Cord (15); remove all packaging material 
and discard. Packaging material can be 
recycled.  

3.

Place the quick heater on a level, firm    
surface. Make sure it is in a stable         
position, so that it cannot fall over or fall 
down. A safety distance of at least 40 cm 
from any objects must be kept.