background image

T8601D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

3

69-1626

Fig. 4. Typical hookup in heat and cool 

system with one transformer.

Fig. 5. Typical hookup in heat and cool 

system with two transformers.

Fig. 6. Proper wiring technique.

Mounting Thermostat

1.

Engage tabs at the top of the thermostat and wall-
plate. See Fig. 7.

2.

Press lower edge of case to close and latch.

NOTES: To remove the thermostat from the wall, first pull 

out at the bottom of the thermostat; remove top 

last.

Fig. 7. Mounting thermostat on wallplate.

Using Thermostat Keys

The thermostat keys are used to:
• set current day and time,

• program times and setpoints for heating and cooling,
• temporarily override program temperatures, 

• display present setting, 
• configure Installer Setup, 

• check Self-Test,
• display outdoor temperature (select models),

• set the system operation, 
• set the fan operation. 

See Fig. 8 for the location of the keys.

L1
(HOT)

L2

M10353

FAN
RELAY

Y

G

THERMOSTAT

C

HEAT
RELAY

R

W

COMPRESSOR
CONTACTOR

TRANSFORMER

B

HEAT
DAMPER

COOL
DAMPER

O

1

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT
PUMP SYSTEMS.

AVAILABLE ON SELECT MODELS. OT WIRES MUST HAVE A 
SEPARATE CABLE FROM THE THERMOSTAT CABLE.

2

2

2

1

3

OT

OT

OUTDOOR
TEMPERATURE
SENSOR

3

L1
(HOT)
L2

M10354

FAN
RELAY

Y

G

THERMOSTAT

RC

HEAT
RELAY

R

W

L1
(HOT)
L2

COMPRESSOR
CONTACTOR

HEATING TRANSFORMER

COOLING TRANSFORMER

B

C

HEAT
DAMPER

COOL
DAMPER

O

2

1

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.

JUMPER RC TERMINAL TO R TERMINAL WHEN INSTALLED ON A
ONE TRANSFORMER SYSTEM.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT
PUMP SYSTEMS.

AVAILABLE ON SELECT MODELS. OT WIRES MUST HAVE A 
SEPARATE CABLE FROM THE THERMOSTAT CABLE.

2

3

3

1

1

3

4

OT

OT

OUTDOOR
TEMPERATURE
SENSOR

4

M4826

FOR WRAPAROUND 
INSERTION STRIP 
7/16 IN. (11 MM).

FOR STRAIGHT INSERTION 
STRIP 5/16 IN. (8 MM).

M14628

PRESS LOWER 
EDGE OF CASE 
TO LATCH.

ENGAGE TABS 
AT TOP OF 
THERMOSTAT 
AND WALLPLATE.

A.

B.

Summary of Contents for T8601D













Reviews: