background image

15 

15 

PRECAUTIONS 

This product is engineered to give you years of satisfactory service if handled 
carefully. Here are a few precautions: 

 

Do not immerse the units in water. 

 

Do not clean the units with abrasive or corrosive materials. They may 
scratch the plastic parts and corrode the electronic circuits. 

 

Do not subject the product to excessive force, shock, dust, temperature, 
or humidity, which may result in malfunctions, shorter lifespan, 
damaged batteries, and damaged parts. 

 

Do not tamper with the units internal components. Doing so will 
invalidate the warranty and may cause damage. These units contain no 
user-serviceable parts. 

 

Use only fresh batteries. Do not mix new and old batteries. 

 

Read the user's manual thoroughly before operating the units. 

 

TROUBLESHOOTING 

Check here before contacting customer service. 

 

Issue Symptom 

Solution 

Check batteries 

Cannot locate remote 
sensor  

Check location 

 Press 

and 

hold 

DOWN

 ( 

button on the main unit to search 
for the signal form the remote 
sensor 

Remote sensor 

Data does not match 
data on the main unit 

Initiate manual sensor search 
(Press and hold 

DOWN

 ( 

button on the main unit) 

16 

SPECIFICATIONS

 

Main Unit 

Indoor Temperature 

Proposed operating range: 23.0°F to 122.0°F (-5°C to +50°C) 

Temperature resolution: 0.2°F (0.1°C) 

User-selectable (°F or °C) temperature display 

Maximum number of remote sensors: 1 (one included) 

RF range: Maximum 100 feet (30 meters)   

Readings update interval: every 45 seconds 

Low battery indicators – for remote sensor and main unit 

Clock 

Precise Quartz Time 

12/24 hour time format 

Crescendo 4 minutes alarm with 5 minutes snooze 

Remote Sensor 

Remote Temperature 

Proposed operating range with alkaline batteries: 

-4°F to + 158°F (-20°C to + 70°C) 

Proposed operating range with lithium batteries:   

-38.8°F to +158°F (-38.8°C to + 70°C) 

Temperature resolution: 0.1°C/0.2°F 

RF Transmission Frequency: 433 MHz 

Temperature transmission cycle: approximately 45 seconds   

Low battery indicator 

Wall-mount of Table stand 

Power 

Main unit: 2 AA size (UM-3) 1.5V batteries (not included) 

Remote Sensor: 2 AA size 1.5V batteries (not included) 

Dimensions 

Main unit: 3.02(L) x 5.16 (H) x 1.11(D) inches 

Remote sensor: 2.37(L) x 4(H) x 1 (D) inch 

Summary of Contents for TS03











Reviews: