background image

 

44 

Setup Menus 

Your installer has already set up your system, however, if changes are needed, you can change the settings as described 
below.  

Brightness and Volume Control 

From the "Home" screen, press 

Setup

. Move the 

Brightness/Volume

 slide bar up or down to increase or decrease 

settings.  Press 

Save

 when complete.  If changes are made and you press 

Save

, a pop-up window displays: 

“Information Settings Saved” 

and

 

exits to the home page. 

 

Note

: Pressing 

Back

 without saving will display 

“Aui Setup Changed. Do you want to save it?

 

Yes or No.  Yes

 saves 

the changes. 

No

 discards the change.  

 

Display & Audio Setup 

Display and Audio Setup 

menus let you access Operating Modes. 

Operating Modes 

provides access to: 

Chime Mode, Voice Mode, 

and

 Voice Chime. 

 

  When in Chime Mode the Keypad chimes whenever a door or window is open. 

  When in Voice Mode the Keypad voice annunciates whenever a change in system status occurs such as Armed, 

Disarmed, or Alarms. 

  When in Voice Chime mode the chime mode and voice mode are in effect. The chime beeps followed by voice 

annunciation. 

 
To change these settings, do the following: 

From the "Home" screen, press 

Setup

. Press 

Disp & Audio Setup

  

 and enter your Authorized Code, if 

required. Select 

Chime Mode 

or 

Voice Mode

 to turn the mode on or off.  

Press 

HOME

 or 

BACK

 after making your selection. 

 

 

The Chime feature is intended for convenience and is not intended for life safety purposes or pool alarm and 
does not meet the requirements of UL 2017. 

 
Notes: 

 

If the Chime Mode and Voice Mode are both selected, the Voice Chime is automatically selected. 

 

When the keypad exits the “Operating Modes” screen, your selection is saved. 

 

It may take a few seconds for the Chime Mode to take effect. 

Summary of Contents for Tuxedo Touch

































































Reviews: