background image

CAUTION

a) To reduce the risk of electric shock, use only with the power-supply cord provided or

with a cord set intended for indoor use.

b) Do not use a cracked, frayed, or damaged cord. Inspect the cord periodically.

c) Do not abuse cord - Do not carry product by the cord or yank or pull it to disconnect

d) Disconnect the product from the outlet when not in use.

e) Do not overload. Connect other lighting strings or tree toppers end-to-end up to a

maximum of 216 watts (1.8 Amps) total. Do not interconnect low-voltage products.

)

D

E

U

N

I

T

N

O

C

E

S

U

R SERVICING INSTRUCTIONS (

from the outlet.

USE AND CARE INSTRUCTIONS

a) Before using or reusing, inspect product carefully.  Discard any products that have cut,

damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures,

b) When storing the product, carefully remove the product from wherever it is placed

loose connections, or exposed copper wire.

to avoid any undue strain or stress on the product conductors, connections, and wires.

c) When not in use, store neatly in a cool, dry location protected from sunlight.

EN

7

If the new lamp base does not fit in lampholder, follow the steps below before step 4:

a) Pull the reflector out.

e) Insert the reflector into the base.

b) Remove the base of burned out lamp by straightening lamp leads and gently

c) Thread leads of new lamp through holes in old base with one lead in

d) After lamp is fully inserted into base, bend each

lead up, like other lamps in the light set so that the
leads will touch the contacts inside the
lampholder (always match the long lead of new

pull lamp out.

each hole.

lamp to the hook of lamp base).

1. To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0

The LED lamp has polarity. Do not deliberately

Volt, 0.06 Watt LED lamps only.
change the direction of the LED lamp in the lamp holder.

product

2. Risk of fire. This product does not contain lamp shunts, which allow the

to operate if one lamp burns out. Replace lamps only with the spare lamps
provided with this product.

Summary of Contents for W14L0694









Reviews: