background image

7 4 8 3 X

A I R   U N L O A D E R

A S S E M B L Y

- H E A D

WP230-n

Fig. 7. Air Unloading of Intake Valves on 3/4 HP  Units.

Disconnect power and loosen motor clamping bolts

and slide motor towards unit. If the compressor has a

totally enclosed belt guard, it will have to be removed.

Remove and replace belts. Motor should be held snug
against belts when retightening so that the belt(s) do not

have 

more than  1/2 inch (12 mm) total play. Make

certain alignment is correct, reinstall guard and turn on
power.

NOTE: Sometimes new belts stretch excessively after

being installed; recheck after one week. See
Data Table.

If motor is considered  Af fective,  disconnect power

and replace motor. When installing motor, reset belt
tension.

Many motors

are dual voltage. Check motor

internal wiring against diagrams on motor or inside

of wiring cover plate for proper connections for
voltage being used.

INTAKE AND  EXHAUST  VALVES, UNLOADER

The intake valves, exhaust valves, and unloader

mechanisms can be disassembled for inspection, clean-
ing, or repair in all sizes except the 1/2 HP, The  1/2 HP

unit is a sealed assembly 

in 

the head. In the event the

valves are deemed defective in this unit, replace the head

assembly (Quincy  Part No. 2400-X2P).

On the  1/4 HP unit, remove the two valve locking

nuts in the head and the valve parts can now be removed
for inspection. See Figure 5 for proper order of re-
assembly. The 1/4 and 1/2 HP units 

have 

check valve on

the pressure switch and an unloader.

The  3/4  HP unit and larger units have automatic

unloaders on intake valve(s). The unloader for the 1 HP
unit is shown in Figure 6. All other units (3/4  HP and
up) use the unloader shown in Figure 7. Access to the
intake valves is gained by unscrewing the unloaders from

the head assembly. Exhaust valves can be removed by
unscrewing the hold down caps covering them. See the
Parts 

List 

for the replacement numbers for these units.

Fig. 8, Three-Way Valve Assembly 

 HP).

Fig. 9. Hydraulic Unloader Assembly.

9

 

75-7131

Summary of Contents for WP230A-M





















Reviews: