Honic HN-IRDNT200FS User Manual Download

Page: 3 / 16

Notice Before Using

Default Mode: 1080P AHD Video Output.

If your DVR is TVI, CVI or Analog DVR, please switch

the corresponding video output mode by OSD joystick.

POWER ON

the camera, switch the video output mode

by OSD joystick according to your DVR video type:



LEFT Push 5s to 1000TVL mode for

analog DVR.



RIGHT Push 5s to TVI mode for

1080P TVI DVR

or XVR



DOWN Push 5s to CVI mode for

1080P CVR or

XVR



UP Push 5s to AHD mode for

1080P (N) AHD DVR

or XVR

Note:

5s means 5 seconds

Installation and Operation:

Unpacking and Handling

Each unit is shipped assembled and factory tested.

Ensure that all accessories are removed from the

container before discarding packing material.

Package includes

1x dome camera 4x mounting screws

4x screw anchors 1x install guide

1x user manual 1x drill template

1x Allen wrench

OSD

Summary of Contents for HN-IRDNT200FS

















Search results

Summary of Contents for HN-IRDNT200FS

Reviews:

Related manuals for HN-IRDNT200FS

Brands by name

Popular brands

Honic HN-IRDNT200FS, User Manual

Search results

Summary of Contents for HN-IRDNT200FS

Reviews:

Related manuals for HN-IRDNT200FS

Brands by name

Popular brands