background image

3

ENGLISH

Flitework quality

We, as the kit manufacturer, provide you with a top quality kit and instructions, but ultimately the quality and fl yability 

of your fi nished model depends on how you build it; therefore, we cannot in any way guarantee the performance 

of your completed model and no representations are expressed or implied as to the performance or safety of your 

completed model.

3

Introduction

Congratulations for purchasing the Flitework Edge 540-M. We say thanks for your trust and we wish you a lot of happy 

fl ights with your new Edge 540M.

The Edge 540 is one of the best competition planes in the world. The pilots of the Red Bull Airrace commit this versions 

very successful in diff erent contests.

Also the Flitework Edge 540M is one of the best aerobatic and 3D models in this class. And we wish you a lot of plea-

sure with this model.

Attention please!

Remote controlled model planes are not a toy! For assembling, fl ying and servicing such models, you need a high 

grade of technical comprehension and liability. Careless assembling and operation may cause personal and material 

damage.

Because the Flitework GmbH has no infl uence on assembly, RC installation, operation and servicing of the fl ight 

device, any liability is rejected under explicit advice to these dangers.

Summary of Contents for FLW4090

















Reviews: