Cleaning the exhaust filter:
1. To remove the exhaust filter, unclip the exhaust filter cover
[20]
and remove the exhaust
filter pack.
[21]
2. Wash the filter in hand warm water
[19]
and allow it to dry thoroughly before replacing
in the cleaner.
REmEmBER:
Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a genuine Hoover replacement. Do not try and use the product
without a dust bag or filter fitted.
Cleaning the permanent cloth dust bag* :
To maintain optimum performance we recommend that you wash the permanent cloth
dust bag under hand warm water after every 5 full bags. Remove excess water and leave
to dry fully before replacing.
Removing a Blockage From The System
If the Bag Check Indicator is red:
1. Check if the bag is full. If so refer to ‘Replacing The Dust Bag’.
2. If is not full, then;
A.
Do the filters need cleaning? If so refer to ‘Cleaning the Filter’.
B.
Check if there is any other blockage in the system - Use a rod or a pole to remove
any blockage from Telescopic Tube or flexible hose.
warning*
: The bag check indicator will remain illuminated if the cleaner is used when
the bag is full, if there is a blockage or if the filters are dirty. If used for a period over ten
minutes with the bag check indicator illuminated, an electronic cut out will switch the
cleaner off to prevent any risk of overheating. If this should happen, switch the cleaner off,
unplug and correct the fault (see ‘Removing a blockage’). The cut out will automatically
reset upon switching the cleaner back on.
ACCESSORIES AND NOZZlES
*Certain models Only ** Certain models only, nozzles may vary according to model
3
GB
To obtain the best performance and energy efficiency
#1
it is recommended that the
correct nozzles are used for the main cleaning operations. These nozzles are indicated in
the diagrams by the letters
GP
,
HF
or
CA
.
A nozzle type
GP
can be used to clean both carpet and hard floor.
A nozzle type
HF
is suitable for use only on hard floor.
A nozzle of type
CA
is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended for
occasional use only.
It is important to note that this vacuum cleaner is supplied with an Energy Label as required
by European Regulation (EU) 665/2013.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this
indicates that the vacuum cleaner is not suitable use on carpets.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then
this indicates that the vacuum cleaneris not suitable for use on hard floors.
#1
NOTE:
Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency
in accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
The Crevice tool, Furniture nozzle and Dusting brush are stored on board under the
accessories door.
[22]
All accessories can be fitted to the end of the handle or the end of the Telescopic* Tube.
Crevice Tool
– For corners and hard to reach areas.
[23]
Furniture Nozzle
– For soft furniture and fabrics.
[24]
Dusting Brush
– For bookshelves, frames, keyboards, etc.
[25]
Pet Hair Remover Turbo Nozzle
* - Use the mini turbo nozzle on stairs or for deep cleaning
on textile surfaces and other hard to clean areas. Particularly suitable for pet hair removal.
[1V]
Allergen Remover mini Turbo Nozzle*
– Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal.
[1w]
Grand Turbo Nozzle*
- Use the Grand Turbo Nozzle for deep cleaning on carpets.
[1X]
Hard Floor Caresse Nozzle*
- For parquet floors and other delicate floors.
[1y]
ImPORTANT:
Do not use the Grand Turbo Nozzle on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
USER CHECklIST
should you have a problem with the product, complete this simple user checklist before
calling your local Hoover service.
•
Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
•
Is the dust bag over-filled? Please refer to ‘Cleaner Maintenance’.
•
Is the filter blocked? Please refer to ‘Cleaner Maintenance’.
•
Is the hose or nozzle blocked? Please refer to ‘Removing a blockage from the system’.
•
Has the cleaner overheated? If so, it will take approximately 45 minutes for the cut out to
automatically reset.
ImPORTANT INFORmATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local Hoover
dealer or direct from Hoover. When ordering parts always quote your model number.
Quality
Hoover’s factories have been independently assessed for quality. Our products are made
using a quality system which meets the requirements of IsO 9001.
