Horizon Fitness 24HL711H, Operating Instructions Manual

English

   - 23 -

To use the recording function, you need to connect 

a USB disk or an external hard disk drive to the TV 

and the connected USB disk should have at least 1 

GB capacity and should have 2.0 speed compatibility. 

If the connected USB device does not support 2.0 

speed, an error message will be displayed.

Note

: Recorded programmes are saved into the 

connected USB disk. If desired, you can store/copy 

recordings onto a computer; however, these files will 

not be available to be played on a computer. You can 

play the recordings only via your TV.

Note

: Lip Sync delay may occur during the timeshifting. 

Radio record is supported. The TV can record 

programmes up to ten hours.
Recorded programmes are split into 4GB partitions. 
If the writing speed of the connected USB disk is not 

sufficient, the recording may fail and the timeshifting 

feature may not be available.
It is recommended to use USB hard disk drives for 

recording HD programmes.
Do not plug out the USB/HDD during a recording. This 

may harm the connected USB/HDD.
Multipartition support is available. The maximum of 

two different partitions are supported. The first partition 

of the USB disk is used for PVR ready features. It also 

must be formatted as the primary partition to be used 

for the PVR ready features.
Some stream packets may not be recorded because 

of signal problems, so sometimes video may freezes 

during playback. 
Record, Play, Pause, Display (for PlayListDialog) 

keys can not be used when teletext is ON. If a 

recording starts from timer when teletext is ON, 

teletext is automatically turned off. Also teletext usage 

is disabled when there is an ongoing recording or 

playback. 

Timeshift Recording 

Press 

(PAUSE) button while watching a broadcast 

to activate timeshifting mode. In timeshifting mode, 

the programme is paused and simultaneously 

recorded to the connected USB disk.
Press   (PLAY) button again to resume the paused 

programme from where you stopped. Press the STOP 

button to stop timeshift recording and return to the 

live broadcast.

Note

: Timeshift cannot be used while in radio mode.

Note

 : You cannot use the timeshift fast reverse feature before 

advancing the playback with the fast forward option.

Instant Recording

Press 

 (RECORD) button to start recording an 

event instantly while watching a programme. You can 

press 

 (RECORD) button on the remote control 

again to record the next event on the EPG. In this 

case, an OSD will be displayed, indicating the 

programmed events for recording. Press   (STOP) 

button to cancel instant recording. 

Note

: You can not switch broadcasts or view the Media Browser 

during the recording mode. While recording a programme or 

during the timeshifting, a warning message appears on the 

screen if your USB device speed is not sufficient.

Watching Recorded Programmes 

Select the 

Recordings Library

 from the 

Media 

Browse

r menu. Select a recorded item from the list (if 

previously recorded). Press the 

OK

 button to view the  

Play Options

. Select an option then press 

OK

 button.

Note: Viewing main menu and menu items will not be available 

during the playback.

Press the   (STOP) button to stop a playback and 

return to the Recordings Library.

Slow Forward

If you press   (PAUSE) button while watching 

recorded programmes, the slow forward feature will 

be available. You can use 

 button to slow forward. 

Pressing 

 button consecutively will change slow 

forwarding speed.

Recording Configuration

Select the Recording Configuration item in the 

Settings menu to configure the recording settings. 

Format Disk

: You can use Format Disk feature 

for formatting the connected USB disk. Your pin is 

required to use the Format Disk feature (default pin 

is 0000).

Default PIN code can change depending on the 

selected country.

If you are asked to enter a PIN code for viewing a 

menu option, use one of the following codes: 

4725

, 

0000

 or 

1234

.

IMPORTANT

: Note that ALL the data stored on the 

USB disk will be lost and the disk format will be 

converted to FAT32 if you activate this feature. If 

your USB disk malfunctions, you can try formatting 

the USB disk. In most cases formatting the USB disk 

will restore normal operation; however, ALL the data 

stored on the USB disk will be lost in such a case. 

Note:

If “USB is too slow” message is displayed on the 

screen while starting a recording, try restarting the recording. 

If you still get the same error, it is possible that your USB 

disk does not meet the speed requirements. Try connecting 

another USB disk.