Horizon Hobby Blade 350 QX BNF, Instruction Manual

6

EN

Transmitter

Model 
Type

Reverse 
Setup

Throttle 
Cut 
Setup

Mode Setup

Switch Positions

Throttle Cut

Return Home

Dual Rate 
Switch

High 
Rate

Low 
Rate

DX4e (New)*
w/3-position 
switch

N/A

N/A

N/A

N/A

Position 0 = 

SMART Mode

Lower throttle 
trim until motors 
stop turning

Press and Hold 
TRAINER/BIND 
Release to EXIT

Rate

100%
fi xed

70%
fi xed

Position 1 = 

Stability Mode

Position 2 = 

Agility Mode

DX5e (New)*
w/3-position 
switch

N/A

N/A

N/A

N/A

Position 0 = 

SMART Mode

Lower throttle 
trim until motors 
stop turning

Press and Hold 
TRAINER/BIND 
Release to EXIT

Rate

100%
fi xed

70%
fi xed

Position 1 = 

Stability Mode

Position 2 = 

Agility Mode

DX6i

Acro

THRO-N
ELEV-N
GEAR-R
AILE-N
RUDD-N
FLAP-N

ACT

Travel Adj: GEAR POS (0) GEAR: 

↑

100%;

GEAR/F MODE POS (1) GEAR: 

↓

40%

FLAPS: Norm 

←↑

100; LAND 

↓

100

MIX 1: ACT;  GEAR 

→

 GEAR 

ACT

RATE D 

0%; U + 100%

SW MIX 

TRIM INH

SUB TRIM 

THRO 

↑

15-20%

GEAR 0; Mix 0 = 

SMART Mode

Press throttle cut

FLAP Position 0 
= OFF

FLAP Position 2 = 
Return Home

ELEV-AIL D/R 100% 70%

GEAR 1; Mix 0 = 

Stability Mode

GEAR 1; Mix 1 = 

Agility Mode

DX7/7SE

Acro

FLAP-R (6)
Others-N

N/A

Travel Adj: GEAR (0)

↑

100%;

GEAR (1) 

↓

40%

MIX 1: FLAP 

→

   Gear OFF/ON

 RATE 

→

 -50%

 0%
 

SW: MIX 

OFFSET: 0

GEAR (0);
Mix (0) = 

SMART Mode

Lower throttle 
trim until motors 
stop turning

FLAP Pos 0
= OFF

FLAP Pos 1
= Return Home

ELEV-AIL D/R 100% 70%

GEAR (1);
Mix (0) = 

Stability Mode

GEAR (1);
Mix (1) = 

Agility Mode

DX7S

Acro

AUX1-R
Others-N

Set To: 
Trainer

Switch Select:
Move Gear to F MODE (F MODE:GEAR)
Leave FLAPS as AUX1
Set All Others to INH
MIX 1: GER > GER
RATE: 0%
 -100%
OFFSET: 0%; TRIM: INH; SW: Mix0

F MODE (0) = 

SMART Mode

Press
Trainer

FLAP Pos 0 = OFF
FLAP Pos 2 = 
Return Home

ELEV-AIL D/R 100% 70%

F MODE (1) = 

Stability Mode

F MODE (1);
HOLD (1) = 

Agility Mode

DX8

Acro

AUX1-R
Others-N

Set To: 
Trainer

Switch Select: F-Mode to Gear;
 

Flap to Aux 1

All Others to INH

F MODE (0) = 

SMART Mode

Press Trainer/
Bind

FLAP Pos 0
= OFF

FLAP Pos 2
= Return Home

ELEV-AIL D/R 100% 70%

F MODE (1) = 

Stability Mode

F MODE (2) = 

Agility Mode

DX9/DX18

Acro

AUX1-R
Others-N

Set To:
I (BIND)

Channel Assign: NEXT
1-4: N/A 

5 Gear: B

6 AUX1: D 

7 AUX2: I

8-10: INH

B (0) = 

SMART Mode

Press I (BIND)

D (FLAP) Pos 0 
= OFF

D (FLAP) Pos 2 = 
Return Home

ELEV-AIL D/R 100% 70%

B (1) = 

Stability Mode

B (2) = 

Agility Mode

*  Old versions of the DX4e and DX5e (with 2-position channel 5 switches) are 

not

 recommended for the 350 QX. Only 

Smart Mode

 and 

Agility Mode

 will be 

available with GPS On.

Transmitter Setup (BNF)

CAUTION:

 When using a Futaba transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module 

manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.