Horizon Hobby Blade 350 QX2, Instruction Manual

5

EN

The Battery Charging Process

1. Connect the AC power supply to the charger.

2. Connect the AC power supply to an AC power source. 

The green LED blinks.

3. Connect the battery to the charger. The red LED 

blinks, indicating charging. When the battery nears 
full charge, the red and green LEDs blink, indicating 
cell balancing.

4. Disconnect the battery when the green LED glows 

solid.

Charging the Flight Battery

Charger Specifi cations

• Input Voltage: 10.5–15V DC
• Charge Current: 3.5A

LED Indications

Green Blinking:

 Ready to Charge

Red Blinking:

 Charging

Red & Green Blinking:

 Cell Balancing

Green Solid:

 Charging Complete

Red Solid:

 Error

CAUTION:

 Overcharging a battery can cause 

a fi re.

NOTICE:

 If using a battery other than the included 

Li-Po battery, refer to your battery manufacturer’s 
instructions for charging.

1a

1b

2

3

*  Old versions of the DX4e and DX5e (with 2-position channel 5 switches) are 

not

 recommended for the 350 QX2. Only 

Smart Mode

 and 

Stability Mode

 will be available with GPS On.

Transmitter Setup

CAUTION:

 When using a Futaba transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding 

and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

Transmitter

Model 
Type

Reverse 
Setup

Throttle Cut 
Setup

Mode Setup

Switch Positions

Throttle Cut

Return Home

DX4e (New)*
w/3-position 
switch

N/A

N/A

N/A

N/A

Position 0 = 

SMART Mode

Lower throttle trim 
until motors stop 
turning

Press and Hold TRAINER/
BIND Release to EXIT

Position 1 = 

AP Mode

Position 2 = 

Stability Mode

DX5e (New)*
w/3-position 
switch

N/A

N/A

N/A

N/A

Position 0 = 

SMART Mode

Lower throttle trim 
until motors stop 
turning

Press and Hold TRAINER/
BIND Release to EXIT

Position 1 = 

AP Mode

Position 2 = 

Stability Mode

DX6i

Acro

THRO-N
ELEV-N
GEAR-R
AILE-N
RUDD-N
FLAP-N

ACT

Travel Adj: GEAR POS (0) GEAR: 

↑

100%;

GEAR/F MODE POS (1) GEAR: 

↓

40%

FLAPS: Norm 

←↑

100; LAND 

↓

100

MIX 1: ACT;  GEAR 

→

 GEAR ACT

RATE D  0%; U + 100%

SW MIX  TRIM INH

SUB TRIM 

THRO 

↑

15-20%

GEAR 0; Mix 0 = 

SMART Mode

Press throttle cut

FLAP Position 0 = OFF
FLAP Position 2 = Return 
Home

GEAR 1; Mix 0 = 

AP Mode

GEAR 1; Mix 1 = 

Stability Mode

DX7/7SE

Acro

FLAP-R (6)
Others-N

N/A

Travel Adj: GEAR (0)

↑

100%;

GEAR (1) 

↓

40%

MIX 1: FLAP 

→

   Gear OFF/ON

 RATE 

→

 -50%

 0%
 

SW: MIX 

OFFSET: 0

GEAR (0); Mix (0) = 

SMART Mode

Lower throttle trim 
until motors stop 
turning

FLAP Pos 0
= OFF
FLAP Pos 1
= Return Home

GEAR (1); Mix (0) = 

AP Mode

GEAR (1); Mix (1) = 

Stability Mode

DX7S

Acro

AUX1-R
Others-N

Set To: 
Trainer

Switch Select:
Move Gear to F MODE (F MODE:GEAR)
Leave FLAPS as AUX1
Set All Others to INH
MIX 1: GER > GER
RATE: 0%
 -100%
OFFSET: 0%; TRIM: INH; SW: Mix0

F MODE (0) = 

SMART Mode

Press
Trainer

FLAP Pos 0 = OFF
FLAP Pos 2 = Return 
Home

F MODE (1) = 

AP Mode

F MODE (1); HOLD (1) = 

Stability Mode

DX8

Acro

AUX1-R
Others-N

Set To: 
Trainer

Switch Select: F-Mode to Gear;
 

Flap to Aux 1

All Others to INH

F MODE (0) = 

SMART Mode

Press Trainer/Bind

FLAP Pos 0
= OFF
FLAP Pos 2
= Return Home

F MODE (1) = 

AP Mode

F MODE (2) = 

Stability Mode

DX6/DX9/DX18 Acro

AUX1-R
Others-N

Set To:
I (BIND)

Channel Assign: NEXT
1-4: N/A 

5 Gear: B

6 AUX1: H 

7-10: INH

B (0) = 

SMART Mode

Press I (BIND)

D (FLAP) Pos 0 = OFF
D (FLAP) Pos 2 = Return 
Home

B (1) = 

AP Mode

B (2) = 

Stability Mode