background image

EN

Blue Angels F-18 80mm EDF

18

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product 
purchased (the “Product”) will be free from defects in materials and workmanship at 
the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage 
due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to 
improper use, installation, operation or maintenance, (iii) modifi cation of or to any part 
of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized 
service center, (v) Product not purchased from an authorized Horizon dealer, (vi) 
Product not compliant with applicable technical regulations, or (vii) use that violates 
any applicable laws, rules, or regulations. 
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY 
OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, 
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER 
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL 
SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE. 

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that 
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by 
Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) 
involved in a warranty claim. Service or replacement decisions are at the sole 
discretion of Horizon. Proof of purchase is required for all warranty claims.  SERVICE 
OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S 
SOLE AND EXCLUSIVE REMEDY. 

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL 
LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, 
WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF 
LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price 
of the Product on which liability is asserted. As Horizon has no control over use, setup, 
fi nal assembly, modifi cation or misuse, no liability shall be assumed nor accepted for 
any resulting damage or injury. By the act of use, setup or assembly, the user accepts 
all resulting liability. If you as the purchaser or user are not prepared to accept the 
liability associated with the use of the Product, purchaser is advised to return the 
Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to confl ict of law principals). 
This warranty gives you specifi c legal rights, and you may also have other rights which 
vary from state to state. Horizon reserves the right to change or modify this warranty 
at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or 
service. Once assembly, setup or use of the Product has been started, you must contact 
your local distributor or Horizon directly. This will enable Horizon to better answer your 
questions and service you in the event that you may need any assistance. For questions 
or assistance, please visit our website at www.horizonhobby.com, submit a Product 
Support Inquiry, or call the toll free telephone number referenced in the Warranty and 
Service Contact Information section to speak with a Product Support representative. 

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you 
live and use the Product in, please use the Horizon Online Service Request submission 
process found on our website or call Horizon to obtain a Return Merchandise 
Authorization (RMA) number. Pack the Product securely using a shipping carton. 
Please note that original boxes may be included, but are not designed to withstand 
the rigors of shipping without additional protection. Ship via a carrier that provides 
tracking and insurance for lost or damaged parcels, as Horizon is not responsible for 
merchandise until it arrives and is accepted at our facility. An Online Service Request 
is available at http://www.horizonhobby.com/content/service-center_render-service-
center. If you do not have internet access, please contact Horizon Product Support to 
obtain a RMA number along with instructions for submitting your product for service. 
When calling Horizon, you will be asked to provide your complete name, street 
address, email address and phone number where you can be reached during business 
hours. When sending product into Horizon, please include your RMA number, a list of 
the included items, and a brief summary of the problem. A copy of your original sales 
receipt must be included for warranty consideration. Be sure your name, address, and 
RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a 
LiPo battery, please contact the appropriate Horizon Product Support offi ce.

Warranty Requirements 

For Warranty consideration, you must include your original sales receipt verifying the 
proof-of-purchase date. Provided warranty conditions have been met, your Product will 
be serviced or replaced free of charge. Service or replacement decisions are at the 
sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and payment 
will be required without notifi cation or estimate of the expense unless the expense 
exceeds 50% of the retail purchase cost. By submitting the item for service you are 
agreeing to payment of the service without notifi cation. Service estimates are available 
upon request. You must include this request with your item submitted for service. Non-
warranty service estimates will be billed a minimum of ½ hour of labor. In addition you 
will be billed for return freight. Horizon accepts money orders and cashier’s checks, as 
well as Visa, MasterCard, American Express, and Discover cards. By submitting any item 
to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our 
website http://www.horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of 
use and ownership. If received, a non-compliant Product will not be serviced. 
Further, the sender will be responsible for arranging return shipment of the 
un-serviced Product, through a carrier of the sender’s choice and at the 
sender’s expense. Horizon will hold non-compliant Product for a period of 
60 days from notifi cation, after which it will be discarded.

10/15

Contact Information

Country of Purchase

Horizon Hobby

Contact Information

Address

United States
of America

Horizon Service Center (Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd
Champaign, Illinois, 61822 USA

Horizon Product Support (Product Technical Assistance)

productsupport@horizonhobby.com
877-504-0233

Sales

websales@horizonhobby.com
800-338-4639

European Union

Horizon Technischer Service

service@horizonhobby.eu

Hanskampring 9
D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

+49 (0) 4121 2655 100

Summary of Contents for E-flite F-18 Blue Angels 80mm EDF





















Reviews: