66
Programming Guide — JR™ XP8103
“SW OFF” appears when the flap mixing is in
the middle of lower position
Elevator Operating Direction
(D=Down, U=Up)
Indicates the function selected
Elevator to Flap Mixing Value (Range ± 125%)
Indicates current mixing switch activated:
ON:
Always ON
MIX: Mixing Switch
FLP (-) D: ON when Flap Switchs in lower position
FLP (-) U: ON when Flap Switchs in upper position
Press the (+) or (-)
key to adjust the
UP and DN
mixing values or
to select the active
“mixing switch.”
Press either CH key
to select function:
↓
Rate
↓
SW
Press to return the mixing
value to zero or to return the
active mixing switch to ON.
DN
SELECT
CH
CH
CLEAR
UP
↓
Rate
↓
SW
Step 10. Mixing elevator-to-flap:
In Function mode, press the
Up
key until “ELEV-FLAP Mix” appears on your screen. This is the
elevator-to-flap mix. Press the
CH
key move the cursor to SW:. This
allows you to select which switch will be used to turn on/off the
elevator-to-flap mixing. Pressing the (+) key will select one of the
following switches: MIX = mix switch (located on the back right of
the transmitter), FLP-D = flap switch down, FLPU flap switch up,
or ON = always on. (See note.) We suggest selecting the mix switch
mix so the elevator-to-flap mix can be turned on and off independently
of the flaps. After selecting MIX, press the
CH
key to return the cursor
to the rate position. With the mix switch in the forward position, hold
up elevator and press the (+) key until a 35% value is achieved. Up
should result in down flaps. If the flap goes up, reverse the 35%
value from a +35 to a -35 using the (-) key. Now hold down elevator
with the control stick and press the (+) key until 35% is achieved.
The flaps should go up. Reverse the value if necessary until up
elevator gives down flaps and down elevator gives up flaps. Later
you can experiment with more or less flap throw by changing this
value. 35% is a good, safe place to start.
At rate, press to
increase/decrease mixing
value (± 125%).
At switch, press to change
switch Selection.
Press either CH key to
manipulate the arrow
from Rate to SW.
At rate, press to set mixing value to
factory preset (0%). At switch,
press to set switch to factory preset
(ON).
DN
SELECT
CH
CH
CLEAR
UP
Indicates the function
being selected:
“SW OFF” appears when the Flap Mixing is in the middle or
upper position
Aileron to Flap Mixing Value (Range ± 125%)
Indicates current mixing switch activated:
ON:
Always ON
MIX: Mixing Switch
FLP (-) D: ON when Flap Switchs in lower position
FLP (-) U: ON when Flap Switchs in upper position
Step 11. Aileron-to-flap mixing:
Press the
Up
key until the “AILE-
FLAP Mix” screen appears. Press the
CH
key to move the cursor to the
“SW:” position. The “SW:” allows you to select which switch is used to
turn on/off the aileron-to-flap mix. Pressing the (+) key will select one
of the following switches: MIX = mix switch located on the back right
of the transmitter, FLP-D = flap switch down, F-U&D = flap switch up
and down, and ON = always on. (See note.)
We recommended putting the aileron-to-flap mix on the mix switch so
the mix can be turned off independently from the flaps. After selecting
“MIX,” press the
CH
key to return the cursor to the “Rate” position.
Now press the (+) key until +100% value is reached. Now the flaps
should move in unison in the same direction with the ailerons. If they
move in opposite directions, press the (-) key until a -100% value is
reached.
↓
Rate
↓
SW
Note:
Switch Assignments for MIX
(mix switch) located on the
back right of the transmitter:
FLP-D = flap switch down
FLPU = flap switch up
ON = always on
