background image

14

EN

Warranty and Service Contact Information

Country of 

Purchase

Horizon Hobby

Contact Information

Address

United States
 of America

Horizon Service Center
(Repairs and Repair Requests)

servicecenter.horizonhobby.com/ RequestForm/

2904 Research Rd
Champaign, IL 61822

Horizon Product Support
(Product Technical Assistance)

productsupport@horizonhobby.com
877-504-0233

Sales

websales@horizonhobby.com
800-338-4639

European Union

Horizon Technischer Service

service@horizonhobby.eu

Hanskampring 9
D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

+49 (0) 4121 2655 100

IC Information

FCC Information

Contains IC: 6157A-BLH03201
CAN ICES-3 (B)/NMB-3(B) 

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to 

the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may 
cause undesired operation of the device.

Contains FCC ID: BRWBLH03201

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications.

NOTICE:

 Modifi cations to this product will void the user’s authority to operate this equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with 
the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

Supplier’s Declaration of Conformity
UMX Mig 15 BNF Basic SAFE (EFLU6050)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

CAUTION: 

Changes or modifi cations not expressly approved by the party responsible for compliance could void 

the user’s authority to operate the equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC 
4105 Fieldstone Rd.,
Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: HorizonHobby.com

Summary of Contents for UMX MiG 15 DF

















Reviews: