Thank you for purchasing the Hornady Lock-N-Load
®
Sonic Cleaner.
™
Please read these instructions before using this machine. If you have
any questions about this accessory, contact us at 1-800-338-3220.
The Hornady Lock-N-Load
®
Sonic Cleaner
™
removes carbon residue from
the inside and outside of cartridge cases with high frequency ultrasonic
energy and a specialized cleaning solution. Unlike case tumblers, the
Lock-N-Load
®
Sonic Cleaner
™
effectively cleans the inner surfaces
of cartridge cases as well as the primer pockets. The Lock-N-Load
®
Sonic Cleaner
™
features a 2 liter stainless steel tank, removable basket,
heating function, and a digital timer. The Lock-N-Load
®
Sonic Cleaner
™
may also be used to clean other small parts.
The primary function of the Lock-N-Load
®
Sonic Cleaner
™
is to
chemically and mechanically clean a variety of items. It may or may
not produce “shiny” brass. To create bright and polished brass we
recommend using the Hornady Case Tumbler. Not all carbon buildup
and tarnish may be removed from cases due to the corrosive nature of
some primer residue and/or deep corrosion.
DE-GAS FUNCTION
The Hornady Lock-N-Load
®
Sonic Cleaner
™
includes a de-gassing
function to remove excess air bubbles from the solution, improving
the effectiveness of the ultrasonic cleaning action. The de-gassing
function cycles the unit on and off, causing air bubbles to release from
the solution and float to the surface. To turn on the de-gas function,
press the FUNCTION button repeatedly until the symbol above the
De-gas label is illuminated. Then turn the unit on by pressing the ON/
OFF button. After de-gassing for 90 seconds, the unit will return to
regular ultrasonic cleaning until the timer expires.
HEATING FUNCTION
The Hornady Lock-N-Load
®
Sonic Cleaner
™
includes a heating
function to further enhance the ultrasonic cleaning action. The
heating function may be used on must gun components, however
caution should be used with any heat sensitive items.
Most brass cartridges do not need heat to efficiently clean. Using the
heating function during prolonged cleaning cycles may actually cause
tarnishing to appear.
To turn on the Heating function, press the HEAT button until the heater
light turns on. The unit will then heat to approximately 135°F when the
ultrasonic cleaner is turned on. The heater light will continue to flash
until the solution reaches the target temperature of 135°F, at which
time the light will turn off.
CLEANING INSTRUCTIONS – BRASS CASES
Before you start cleaning cavses, make sure all spent primers have
been removed with a full-length die, neck die or the Hornady Universal
De-Capping Die (050085). This will greatly enhance the cleaning of
primer pockets.
Place cases in basket and lower into tank. Add enough water so the
cases are completely submerged but do not exceed the MAX water
line which appears on the side of the basket and tank. Mix solution
according to instructions on bottle. Cases must NOT come into contact
with the tank!
Plug in power cord and set the timer by pressing the
s
button until the
desired cycle time appears. Pressing the
s
button multiple times will
increase the timer in 5 minute intervals from 5 to 30 minutes. Pressing
the
t
button will decrease the timer by 1 minute.
The heating function does not need to be used on cartridge brass and
may actually cause tarnishing to appear.
When using new solution, or there appears to be small air bubbles in
the solution, it is recommended to run the de-gassing function prior to
cleaning. This can be done after the parts are added and will remove
many of the air bubbles in the solution, causing the Lock-N-Load
®
Sonic Cleaner
™
to run more efficiently. See previous instructions in
“DE-GAS FUNCTION.”
Press the ON/OFF button to stop or pause a cycle. Pressing the ON/
OFF button again will restart the current cycle.
Check cases periodically to determine appropriate cleaning time.
Most cases will be clean after 10-20 minutes, however longer cycles
may be needed for cases with heavy carbon buildup. If running longer
than 30 minutes, allow unit to cool for approximately 5 minutes before
continuing additional cleaning cycles.
Unplug power cord and drain cleaning solution into tank by lifting and
tilting basket with the cleaned cases. Rinse cleaning solution from
the cases. De-ionized water will minimize water spots on the cases
while they’re drying. When finished cleaning cases, unplug unit and
pour used solution out over the back of the tank. This will minimize the
possibility of water making contact with the internal components. Do
not pour cleaning solution out over the front of the unit.
CLEANING INSTRUCTIONS – OTHER ITEMS
The previous steps can be used to clean other items such as small
gun components, metallic shooting and reloading equipment as
well as other waterproof household items. If you wish to clean
sensitive or valuable items, use distilled water in the tank without
any type of detergent or cleaning solution. Never use the heating
function on sensitive items. Read and follow instructions on cleaning
solution bottles. Do not use the Hornady One Shot
®
Sonic Clean
™
Brass Solution to clean non-brass items, as it may harm some
finishes. Thoroughly rinse the inside of the Hornady Lock-N-Load
®
Sonic Cleaner
™
tank when switching cleaning solutions. Oversized
items that do not fit in the tank can be cleaned by partially submerging
one end and then rotating and repeating the cleaning cycles.
MAINTENANCE
If the unit will not be used for an extended period of time, unplug the
power cord, empty the tank and rinse it with fresh water.
Use a damp towel to remove any chemical residue from the tank. Use
a soft clean towel to dry the surface of the tank and store the unit in
a cool/dry location. Renew cleaning solution often to maintain the
efficiency and performance of the Lock-N-Load
®
Sonic Cleaner.
™
Solutions, as with most chemicals, will become spent over time.
Replenish solution when it becomes visibly dirty or if you notice a
decrease in cleaning effectiveness.
WARRANTY
Hornady Manufacturing warrants to you that for one year from the
date of purchase, your Lock-N-Load
®
Sonic Cleaner
™
will be free from
defects in material and workmanship. This warranty does not cover
damage caused by normal wear, accidents, abuse or failure to provide
proper care and maintenance.
SPECIFICATIONS
Model Number:
043321
Tank Dimensions:
7.2" x 6" x 3" (2.1 Qt.)
Maximum Part(s) Weight:
2 pounds
Timer Settings:
1-30 Minutes
Power Supply:
AC 220-240V 50Hz
Power:
160W Total
Frequency:
35000 Hz
