HORNER Shearing Longhorn 3.2 Instruction Booklet Download

Page: 9 / 16

LONGHORN 12V INSTRUCTION MANUAL

SOLID DRIVE LUBRICATION

FLEXI DRIVE LUBRICATION

Oiling the driveshaft

Frequency:

After every 4 hours of use

Directions

• Remove the handpiece and the driveshaft

• Add oil into the top of the driveshaft (1)

• Add oil into the top of the long tube (2)

• Oil the elbow cogs (3)

• Oil the holes in the elbow joints (4 + 5)

• Add oil into the oil hole on the short tube (6)

Greasing the driveshaft

Frequency:

After every 40 hours of use or annually

Directions (long gut)

• Unscrew the ferule from the solid elbow

• Unhook the long gut from the eye spindle

• Remove the long gut

• Refit the long gut whilst applying grease

• Hook the long gut onto the eye spindle

• Screw the ferule back onto solid elbow

Directions (short gut)

• Slacken the clamp on short tube

• Remove the short tube

•

Grease the short gut

• Refit short tube

• Tighten clamp

SAE 30

LONGHORN

OIL

LONGHORN

OIL

LONGHORN

OIL

LONGHORN

OIL

LONGHORN

OIL

LONGHORN

OIL

Summary of Contents for Longhorn 3.2

















Search results

Summary of Contents for Longhorn 3.2

Reviews:

Related manuals for Longhorn 3.2

Brands by name

Popular brands

HORNER Shearing Longhorn 3.2, Instruction Booklet

Search results

Summary of Contents for Longhorn 3.2

Reviews:

Related manuals for Longhorn 3.2

Brands by name

Popular brands