6
GB
Instruction
WHEN OPERATING THE APPLIANCE
If you are going to use the tool, vapours and gas can be released during a short time. This can be
•
harmful for your health. Asthmatics can suffer hindrance of it.
Before connecting the plug to the mains voltage you have to check if the switch is in position“0”.
•
Keep the mains lead always away from the nozzle of the tool.
•
Keep children and animals away from the appliance if you are using it.
•
Keep all parts of the body away from the metal heating head. Do not touch it before it is cooled down.
•
Carry the appliance by the handle, even when the metal heating head is cooled down.
•
Hold the appliance by the insulated parts, as well during as after use and make sure, the cable cannot
•
touch any hot parts.
IMMEDIATELY SWITCH OFF THE APPLIANCE WHEN
Plug and/or cable are defective or damaged.
•
The switch is defective.
•
You smell or see smoke caused by scorched insulation from the appliance.
•
ELECTRICAL SAFETY
When using electric machines always observe the safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also
the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
Class II machine – Double insulation – You don’t need any earthed plug.
Replacing cables or plugs
If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person, in order to avoid a hazard. Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum
conductor size is 1.5 mm2. When using a cable reel always unwind the reel completely. Inadequate
extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and
the connection has to be kept dry and off the ground. It is recommended that this is accomplished by
means of a cord reel which keeps the socket at least 60 mm above the ground.
OPERATION
Always use with caution! Do NOT cover the ventilation openings during use as it
causes a risk of burns! Do not touch the hot nozzle!
Temperature settings
With the temperature switch you can select from two temperature settings. Depending on the
application,you can use the following settings:
Setting I: 50°C (cooling)
Setting II: 600°C
The volume of air in each setting: 500 litres/minute.
ELECTRICAL SAFETY
When using electric machines always observe the safety regulations applicable in your country to
reduce the risk of fi re, electric shock and personal injury. Read the following safety instructions and also
the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
Class II machine – Double insulation – You don’t need any earthed plug
Replacing cables or plugs
If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualifi ed person, in order to avoid a hazard. Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable reel always unwind the reel completely. Inadequate
extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and
the connection has to be kept dry and off the ground. It is recommended that this is accomplished by
means of a cord reel which keeps the socket at least 60 mm above the ground.
OPERATION
Always use with caution! Do NOT cover the ventilation openings during use as it
causes a risk of burns! Do not touch the hot nozzle!
Temperature settings
With the temperature switch you can select from two temperature settings. Depending on the applica-
tion, you can use the following settings:
Setting I:
50°C (cooling)
Setting II:
600°C
The volume of air in each setting: 500 litres/minute
To turn on the power
Slide the switch
to position II, the unit is switched on.
To cool the device
After working with the device at high temperature setting (Setting II), the device is getting very hot. So
it is suggested to slide the switch
to setting I, to quickly cool down the device before turning it off
and storing it.
ENGLISH
7
BSI0616bsThKi_19489.indd 7
16/09/16 10:33
ELECTRICAL SAFETY
When using electric machines always observe the safety regulations applicable in your country to
reduce the risk of fi re, electric shock and personal injury. Read the following safety instructions and also
the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
Class II machine – Double insulation – You don’t need any earthed plug
Replacing cables or plugs
If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualifi ed person, in order to avoid a hazard. Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable reel always unwind the reel completely. Inadequate
extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and
the connection has to be kept dry and off the ground. It is recommended that this is accomplished by
means of a cord reel which keeps the socket at least 60 mm above the ground.
OPERATION
Always use with caution! Do NOT cover the ventilation openings during use as it
causes a risk of burns! Do not touch the hot nozzle!
Temperature settings
With the temperature switch you can select from two temperature settings. Depending on the applica-
tion, you can use the following settings:
Setting I:
50°C (cooling)
Setting II:
600°C
The volume of air in each setting: 500 litres/minute
To turn on the power
Slide the switch
to position II, the unit is switched on.
To cool the device
After working with the device at high temperature setting (Setting II), the device is getting very hot. So
it is suggested to slide the switch
to setting I, to quickly cool down the device before turning it off
and storing it.
ENGLISH
7
BSI0616bsThKi_19489.indd 7
16/09/16 10:33
Summary of Contents for 211-320
