Hosen lighting Technology Limited
RGBW
4In1
8W6PCS
Indoor
Wall
Washer
Current
3
Page
，
Total
7Page(s)
side
into
OUT
signal
connector
in
the
DMX
512
board(signal
input:
1=>Ground,
2=>Data,
3=>data+).
3.
To
connect
the
cable
and
put
into
power,
them
the
light
stays
in
the
status
to
receive
the
operation
signal
like:
Music,
Automatic,
and
DMX512ect.
Take
note:
Please
out
off
the
power
line
if
you
will
not
operate
it
for
a
certain
time.
5.2.
Fixture
Linking
To
run
your
light
shows
of
one
or
more
fixtures
using
DMX
‐
512
controller
or
to
run
synchronized
shows
on
two
or
more
fixtures
in
master/slave
operating
mode,
you
need
DMX
cables
to
link
the
units
from
DMX
IN
to
DMX
OUT.
Notice:
the
length
of
signal
cables
should
be
within
100meters,
to
prevent
the
signal
interference
by
other
appliances
because
of
the
long
signal
cables.
5.3.
AC
Power
The
fixture
is
designed
to
work
on
100
‐
240V
50/60Hz.Before
applying
power
to
a
unit,
check
that
the
source
voltage
matches
the
unit’s
requirement.
6.
Safety
Instructions
This device has left the factory in perfect condition .in order to maintain this condition and to
ensure a safe operation , it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual
Î
If
the
device
has
been
exposed
to
temperature
changes
due
to
environmental
changes,
do
not
switch
it
on
immediately.
The
arising
condensation
could
damage
the
device.
Leave
the
device
switched
off
until
it
has
reached
room
temperature.
This
device
falls
under
protection
‐
class
I.
Therefore,
it
is
essential
that
the
device
be
earthed.
Î
The
electric
connection
must
carry
out
by
qualified
person.
Î
The
device
shall
only
be
used
with
rate
voltage
and
frequency
Î
Make
sure
the
power
cord
is
never
crimped
or
damaged
by
sharp
edges
.if
this
would
be
the
case,
replacement
of
the
cable
must
be
done
by
an
authorized
dealer.
Î
Always
disconnect
from
the
mains
,
when
the
device
is
not
in
use
or
before
cleaning
it
.only
handle
the
power
cord
by
the
plug
.Never
pull
out
the
plug
by
tugging
the
power
cord
Î
During
initial
start
‐
up
some
smoke
or
smell
may
arise
.this
is
a
normal
process
and
does
not
necessarily
mean
that
the
device
is
defective
,
it
should
decrease
gradually.
7.
Operation
Instruction
Î
Don’t
turn
on
the
fixture
if
it’s
been
through
severe
temperature
difference
like
after
transportation
because
it
might
damage
the
light
due
to
the
environment
changes
.So
make
sure
to
operate
the
fixture
until
it
is
in
normal
temperature.
Î
This
light
should
be
keep
away
from
strong
shaking
during
any
transportation
or
movement.
Î
Don’t
expose
the
fixture
in
overheat,
moisture
or
environment
with
too
much
dust
when
installing
it.
And
don’t
lay
any
power
cables
on
the
floor.
Or
it
might
cause
electronic
shock
