26
26
E1CG4880210
E1CG4880210
Fig. 3
Fig. 3
Fig. 4
Fig. 4
Fig. 5
Fig. 5
Bottom
Bottom
Adjustable Leg
Adjustable Leg
Adjustable Leg
Adjustable Leg
Bin Control Switch
Bin Control Switch
Bolt
Bolt
Icemaker
Icemaker
Drain Pipe Collar
Drain Pipe Collar
Packing
Packing
Drain Pan
Drain Pan
Bin Drain Hole
Bin Drain Hole
(P-200SD)
(P-200SD)
Bin Drain Hole
Bin Drain Hole
(F-series)
(F-series)
Storage Bin
Storage Bin
3. INSTALLATION
3. INSTALLATION
* Incorrect installation can cause harm to people,
* Incorrect installation can cause harm to people,
animals or things, for which the manufacturer
animals or things, for which the manufacturer
cannot be held responsible.
cannot be held responsible.
[a] IM-240D, IM-240X
[a] IM-240D, IM-240X
1) Lay the Storage Bin on its rear side carefully to
1) Lay the Storage Bin on its rear side carefully to
prevent damage. Secure the four adjustable
prevent damage. Secure the four adjustable
legs (bin accessory) into the four tapped holes
legs (bin accessory) into the four tapped holes
on the underside of the Bin. See Fig. 3.
on the underside of the Bin. See Fig. 3.
2) Position the Storage Bin in the selected
2) Position the Storage Bin in the selected
permanent position, and level it in both the left-
permanent position, and level it in both the left-
to-right and front-to-rear directions. See Fig. 4.
to-right and front-to-rear directions. See Fig. 4.
3) Remove the icemaker panels. The Rear Panel
3) Remove the icemaker panels. The Rear Panel
is not required to be removed for installation.
is not required to be removed for installation.
See “1. UNPACKING”.
See “1. UNPACKING”.
4) Remove the shipping tape holding the Drain Pan.
4) Remove the shipping tape holding the Drain Pan.
5) Place the icemaker on the top of the Storage
5) Place the icemaker on the top of the Storage
Bin. Be careful not to damage the icemaker
Bin. Be careful not to damage the icemaker
frame and the Bin Control Switch. See Fig. 5.
frame and the Bin Control Switch. See Fig. 5.
6) Secure the icemaker with the two bolts provided.
6) Secure the icemaker with the two bolts provided.
See Fig. 5.
See Fig. 5.
7) Align the Storage Bin drain hole and the drain
7) Align the Storage Bin drain hole and the drain
pan hole. Insert the Packing (bin accessory) and
pan hole. Insert the Packing (bin accessory) and
fasten the Drain Pipe Collar (bin accessory).
fasten the Drain Pipe Collar (bin accessory).
See Fig. 5.
See Fig. 5.
Note:
Note: On the F-series Bins, an extension drain
On the F-series Bins, an extension drain
tube kit is provided which attaches to the
tube kit is provided which attaches to the
icemaker Drain Pan and exits through the
icemaker Drain Pan and exits through the
pre-drilled hole in the side of the Bin.
pre-drilled hole in the side of the Bin.
8) Replace the icemaker panels in their correct
8) Replace the icemaker panels in their correct
positions.
positions.
Summary of Contents for IM-240AME
