36
36
E1CG4880210
E1CG4880210
* Water-cooled model only
* Water-cooled model only
*Cooling Water Inlet
*Cooling Water Inlet
Water Inlet
Water Inlet
Water Inlet
Water Inlet
Drain Outlet (Upper Unit)
Drain Outlet (Upper Unit)
Drain Outlet (Lower Unit)
Drain Outlet (Lower Unit)
Drainage
Drainage
Drain Outlet (Bin)
Drain Outlet (Bin)
Elbow
Elbow
Union
Union
Tee
Tee
Middle Unit
Middle Unit
Lower Unit
Lower Unit
Storage
Storage
Bin
Bin
Upper Unit
Upper Unit
*Cooling Water Outlet
*Cooling Water Outlet
(IM-720)
(IM-720)
*Cooling Water Inlet
*Cooling Water Inlet
*Cooling Water Outlet
*Cooling Water Outlet
Water Inlet
Water Inlet
*Cooling Water Inlet
*Cooling Water Inlet
*Cooling Water Outlet
*Cooling Water Outlet
Drain Outlet (Middle Unit)
Drain Outlet (Middle Unit)
*Cooling Water Inlet
*Cooling Water Inlet
Water Inlet
Water Inlet
Drain Outlet
Drain Outlet
(Icemaker dump)
(Icemaker dump)
Drain Outlet (Bin)
Drain Outlet (Bin)
Drainage
Drainage
*Cooling Water Outlet
*Cooling Water Outlet
Fig. 27
Fig. 27
(IM-240)
(IM-240)
Fig. 26
Fig. 26
Top Panel
Top Panel
Upper Condenser Unit
Upper Condenser Unit
Lower Condenser Unit
Lower Condenser Unit
Screw
Screw
[e] STACKING CONDENSER UNITS
[e] STACKING CONDENSER UNITS
1) Secure the lower Condenser Unit.
1) Secure the lower Condenser Unit.
2) Remove the Top Panel of the lower Condenser Unit.
2) Remove the Top Panel of the lower Condenser Unit.
Keep the four screws for the Top Panel.
Keep the four screws for the Top Panel.
3) Attach the upper Condenser Unit on top of the lower.
3) Attach the upper Condenser Unit on top of the lower.
4) Secure the upper Condenser Unit with the four screws
4) Secure the upper Condenser Unit with the four screws
for the Top Panel.
for the Top Panel.
5) Install refrigerant lines, and make electrical
5) Install refrigerant lines, and make electrical
connections for each Fan Motor as instructed under
connections for each Fan Motor as instructed under
[c] and [d].
[c] and [d].
7. WATER SUPPLY AND DRAIN CONNECTIONS
7. WATER SUPPLY AND DRAIN CONNECTIONS
(For the U.K. only, the connections must be in
(For the U.K. only, the connections must be in
accordance with current requirements of the
accordance with current requirements of the
Model Water Byelaws 1986 SI No. 1147)
Model Water Byelaws 1986 SI No. 1147)
* Only potable water should be used for the
* Only potable water should be used for the
icemaker.
icemaker.
* Water supply pressure should be minimum 0.5
* Water supply pressure should be minimum 0.5
bar and maximum 8 bar. If the pressure
bar and maximum 8 bar. If the pressure
exceeds 8 bar, use a proper pressure reducing
exceeds 8 bar, use a proper pressure reducing
valve. Do
valve. Do NOT
NOT throttle back the supply tap.
throttle back the supply tap.
* A plumbing permit and services of a licensed
* A plumbing permit and services of a licensed
plumber may be required in some areas.
plumber may be required in some areas.
* The icemaker drain is gravity flow, so ensure
* The icemaker drain is gravity flow, so ensure
drain pipe has an adequate pitch or fall.
drain pipe has an adequate pitch or fall.
* Water should drain into an open trap.
* Water should drain into an open trap.
* The Storage Bin has two drain outlets. The
* The Storage Bin has two drain outlets. The
upper/outer one is for dump from the icemaker,
upper/outer one is for dump from the icemaker,
and the lower/inner is for the Bin. The two drain
and the lower/inner is for the Bin. The two drain
lines must be separated to prevent a backflow
lines must be separated to prevent a backflow
into the Storage Bin.
into the Storage Bin.
* On water-cooled model, a back flow preventer
* On water-cooled model, a back flow preventer
may be required in the cooling water circuit.
may be required in the cooling water circuit.
Summary of Contents for IM-240AME
