GB
1
5
Do not position blinds behind the cooker or less
than 200 mm awa
y
from its sides.
An
y
hoods must be installed according to the
instructions listed in the relevant operating manual.
L
evelling
If it is necessar
y
to level the
appliance, screw the
adjustable feet into the places
provided on each corner of the
base of the cooker (
see figure
).
The legs* fit into the slots on
the underside of the base of
the cooker.
E
l
ec
t
r
i
c
a
l
c
onn
ec
t
ion
Install a standardised plug corresponding to the
load indicated on the appliance data plate (
see
Technical data table
).
The appliance must be directl
y
connected to the mains
using an omnipolar circuit-breaker with a minimum
contact opening of 3 mm installed between the
appliance and the mains. The circuit-breaker must be
suitable for the charge indicated and must compl
y
with
current national legislation (the earthing wire must not
be interrupted b
y
the circuit-breaker). The suppl
y
cable
must be positioned so that it does not come into
contact with temperatures higher than 50°C at an
y
point.
Before connecting the appliance to the power
suppl
y
, make sure that:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the ma
x
imum power of
the appliance, which is indicated b
y
the data plate.
The voltage is in the range between the values
indicated on the data plate.
The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use e
x
tension cords or multiple sockets.
Once the appliance has been installed, the power
suppl
y
cable and the electrical socket must be
easil
y
accessible.
The cable must not be bent or compressed.
The cable must be checked regularl
y
and replaced
b
y
authorised technicians onl
y
.
T
he
man
u
f
a
c
t
ur
e
r
de
c
lines
an
y
lia
b
ilit
y
sho
u
ld
these
sa
f
et
y
meas
ur
es
not
b
e
o
b
se
r
ved
.
G
as
c
onne
c
tion
Connection to the gas network or to the gas c
y
linder
ma
y
be carried out using a fle
x
ible rubber or steel
hose, in accordance with current national legislation
and after making sure that the appliance is suited to
the t
y
pe of gas with which it will be supplied (see the
rating sticker on the cover: if this is not the case
see
below
). When using liquid gas from a c
y
linder, install a
pressure regulator which complies with current national
regulations. To make connection easier, the gas
suppl
y
ma
y
be turned sidewa
y
s*: reverse the position
of the hose holder with that of the cap and replace the
gasket that is supplied with the appliance.
Check that the pressure of the gas suppl
y
is
consistent with the values indicated in the Table of
burner and nozzle specifications (
see below
). This
will ensure the safe operation and durabilit
y
of
y
our
appliance while maintaining efficient energ
y
consumption.
G
as
c
onne
c
tion
u
sing
a
f
lexi
b
le
ru
bb
e
r
hose
Make sure that the hose complies with current
national legislation. The internal diameter of the hose
must measure: 8 mm for liquid gas suppl
y
; 13 mm
for methane gas suppl
y
.
Once the connection has been performed, make
sure that the hose:
Does not come into contact with an
y
parts that
reach temperatures of over 50°C.
Is not subject to an
y
pulling or twisting forces and
that it is not kinked or bent.
Does not come into contact with blades, sharp
corners or moving parts and that it is not
compressed.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min.
mm.
420
Min.
mm.
* Onl
y
available in certain models
All manuals and user guides at all-guides.com
