18
it
en
PARTS AND FEATURES
1. Bowl
2.
Strainer holder
3. Strainer
4.
Juice Auger
5. Lid
6.
Rubber pad
7.
Pulp container
8.
Juice container
9. Pusher
10.
Cleaning brush*
* (Only on certain models)
Knob
OFF
— Stops motor.
ON
— Starts motor/makes juice.
The juicer will only function correctly if all its
parts have been assembled correctly and the
lid is in place.
R
— Reverses motor and is to be used only when
food is stuck.
INTRODUCTION
Thank you for purchasing our product.
In doing so, you have opted for an effective high-
performance appliance.
The Slow Juicer is a new type of low-speed slow
grinder for fruit and vegetables. This new Juicer has
two separate outlets for the juice and the pulp. The
method of extraction is masticating and pressing, using
the screw-like auger much like a mortar and pestle.
The action tears open the food’s cell membranes
and releases its deep-seated nutrients and enzymes.
It also releases more phytonutrients, resulting in a
richer coloured juice that retains more vitamins and
minerals. The slow revolutions per minute ensure that
it does not disrupt the cellular structure of fruit and
vegetables, eliminating oxidation and separation. It
consequently preserves the natural form of precious
enzymes and nutrients, even from wheatgrass, soy
and leafy greens.
If the instructions on the correct use of this appliance
are not observed, the manufacturer shall assume no
responsibility for any resulting damage.
The operating instructions may refer to different
models: any difference is clearly identified.
BEFORE FIRST USE
Carefully wipe the outside of the appliance to remove
any dust that may have accumulated. Dry with a dry
cloth. Do not use any harsh abrasive cleaners. Wash
the accessories in warm soapy water. Then dry with
a dry towel. Do not immerse the supply cord or any
motor parts of this appliance in water or other liquids.
This appliance has a built-in safety lock which
ensures that you can only switch the appliance
on if you have assembled the juicer correctly on the
motor unit. When assembled correctly, the built-in
safety lock is inactive.
ASSEMBLING THE JUICER (A)
Under the bowl there is a rubber pad allowing
the discharge of all the juice only from the juice
outlet. Before juicing, make sure the pad is plugged in
completely to prevent any leakage.
Before you assemble the juicer, ensure that the power
cord is unplugged.
1. Put the strainer into the strainer holder.
2. Put the strainer holder into the juice bowl. Be
sure to align the arrow on the strainer with the
arrow on the bowl. When the two arrows are
properly aligned, the strainer should lock into
the bowl, thus preventing it from moving around.
Make sure that the teeth along the lower edge of
the strainer holder fit properly into the cogwheel
inside the bowl.
3. Place the Juice bowl on top of the main body:
make sure the bowl is in place by inserting the
3 hooks on the main body into the 3 slots on
the bowl bottom. Perform a slight rotation in a
clockwise direction until a click is heard.
4. Put the Juice Auger into the strainer and rotate
until it falls into place. To make sure that the
screw is in the correct position, verify that the
upper surface is below the level of the strainer
edge.
5. Fit the lid on the Juice bowl and turn it in position
so it locks into the main body.
6.
Place the pulp tank so that it fits in position on
the left hand side of the juicer’s main body. Be
sure to align the arrow on the lid with the arrow
on the bowl.
7. Place the juice cup under the Juicer spout.
8. Slide the food pusher down the food chute. The
pusher can only fit one way.
Summary of Contents for SJ 4010 Fxy
Page 2: ...220 240V 400W 1 2 3 4 5 7 10 8 9 6 SJ 4010 Fxy ...
Page 3: ...A ...
Page 95: ...95 it bg ...
